Double Swing Check Valves
2Pages

{{requestButtons}}

Catalog excerpts

Double Swing Check Valves - 1

379 VALVOLA DI RITEGNO A DOPPIO BATTENTE TIPO WAFER PN 16 DOUBLE SWING CHECK VALVE WAFER TYPE PN 16 FIGURA 379 GHISA / CAST IRON COSTRUZIONE CONSTRUCTION POS DENOMINAZIONE 1 2 3 4 5 6 INSTALLAZIONE INSTALLATION Prima di montare la valvola accertarsi che linterno del corpo sia completamente pulito. Eventuali impurità dovranno essere rimosse per assicurare un corretto funzionamento, se si dispone di aria compressa utilizzarla per una migliore pulizia. Verificare che le flange ove sarà inserita abbiano i fori in asse, siano parallele e non vi sia troppo o poco spazio tra di esse tenendo conto dello spessore delle guarnizioni impiegate e del loro naturale appiattimento dopo il serraggio dei dadi. Non saldare le flange al tubo quando la valvola é già assemblata. Inserire i tiranti nei fori delle flange e serrarli mantenendo una frequenza diametralmente alternata (per la migliore deformazione della guarnizione). NOTA: per il montaggio fra le flange e la lunghezza dei tiranti vedere pagina 227. Before to assemble the valve at the pipeline check inside the body to be completely clean, possible impurities have to be removed in order to ensure a right functioning. If compressed air is at your disposal, use it for a better cleaning. The counter-flanges of the pipeline must be parallel and have aligned holes. Check the space between them, keeping into account the gaskets and their flattering after nuts closing. Do not weld any flange at the pipeline when the valve is already assembled. Fit the tie-rods in flanges holes, necessarily welding neck type, and tighten them maintaining a diametrically opposed sequence (for a better deformation of the O-rings). NOTA: assembling between flanges and studs length, see page 227. CORPO BATTENTE GUARNIZIONE PERNO MOLLA ANELLO DAL DN 200 MATERIALE PART NAME MATERIAL GHISA EN-GJL-250 GHISA EN-GJS-400-15 EPDM ACCIAIO INOX ACCIAIO INOX ACCIAIO ZINCATO BODY SWING GASKET PIN SPRING RING FROM DN 200 EN-GJL-250 CAST IRON EN-GJS-400-15 C. IRON EPDM STAINLESS STEEL STAINLESS STEEL ZINC PLATED STEEL MANUTENZIONE MAINTENANCE La mancanza di tenuta della sede è dovuta unicamente al logorio nel tempo della guarnizione (3) o a possibili corpi estranei presenti nella tubazione. Se la mancata tenuta è attribuibile ad impurità depositate sulla sede, smontare la valvola dall'impianto e rimuoverle. Per la sua conformazione costruttiva è sconsigliabile smontare la valvola per ripristinare le sedi di tenuta qualora queste siano state rovinate; è pertanto necessario che la riparazione venga eseguita in fabbrica, al fine di collaudare nuovamente la valvola a riparazione avvenuta con appositi apparecchi. The non sealing of the disc seat is exclusively due to the wear of time of the sealing ring (9). If the non sealing is due to impurities in the pipeline, deposited on the seats, disassemble the valve from the plant and remove them. Due to its shape it is not advisable to disassemble the valve to repair the sealing seats, in case they are damaged; therefore it is necessary to repair the valve at a factory, in order to check again the valve once repiared by appropriate machineries. FUNZIONAMENTO FUNCTIONING La valvola funziona sia orizzontalmente che verticalmente purchè il flusso sollevi l'otturatore. Per installazioni verticali escludere il montaggio dall'alto verso il basso. The valve works both horizontally and vertically but if the flow raise the disc. In case of vertical installations, exclude the assembling with the flow direction from top to bottom. L a M I VA L S R L s i r i s e r v a d i a p p o r t a r e m o d i f i c h e s e n z a a l c u n p r e a v v i s o 222

Open the catalog to page 1
Double Swing Check Valves - 2

VALVOLA Dl RTTEGNO A DOPPIO BATTENTE TIPO WAFER DOUBLE SWING CHECK VALVE WAFER TYPEPN16 ESECUZIONE STANDARD / STANDARD EXECUTION Corpo di ghisa. Battente di ghisa sferoidale. Perno e molla d'acciaio inox. Guarnizione EPDM. Adatta ad inserimento tra flange tipo PN 16 e Cast iron body. Bronze swing. Stainless steel pin and spring. NBR gasket. Suitable to be assembled between flanges PN 16 and ANSI 150. Diametri superiori con esecuzione solo PN 1 Esecuzione di acciaio inox Battente di acciaio inox Bigger sizes with only PN 10 Stainless steel Stainless steel swing Nitrocellulose painting BLUE...

Open the catalog to page 2

All Mival catalogs and technical brochures

  1. 346

    2 Pages

  2. MIVAL Products

    72 Pages

  3. 54

    2 Pages

  4. 691

    1 Pages

  5. 266/25

    2 Pages

  6. 150

    2 Pages

  7. 154

    2 Pages

  8. WAFER VALVE

    12 Pages

  9. COMBO VALVE

    20 Pages

  10. PRODUCTS 2014

    64 Pages

Archived catalogs

  1. Float Valves

    2 Pages

  2. 3 way valve

    2 Pages

  3. 3 way valve

    2 Pages

  4. holder valve

    5 Pages

  5. bleed valve

    5 Pages

  6. axial joint

    2 Pages

  7. gate valve

    5 Pages

  8. Catalogue 2010

    12 Pages

  9. MIVAL VALVES

    28 Pages