Group: Mitsubishi
Catalog excerpts
GRAPHIC OPERATION TERMINAL ■MICROCOMPUTER CONNECTION (SERIAL) ■MICROCOMPUTER CONNECTION (ETHERNET) ■DeviceNet CONNECTION ■MODBUS/RTU MASTER CONNECTION ■MODBUS/TCP MASTER CONNECTION ■MODBUS/RTU SLAVE CONNECTION ■MODBUS/TCP SLAVE CONNECTION ■PROFIBUS DP CONNECTION ■SLMP CONNECTION ■CC-Link IE FIELD NETWORK BASIC CONNECTION ■CONNECTION TO SOUND OUTPUT UNIT ■CONNECTION TO EXTERNAL I/O DEVICE ■BAR CODE READER CONNECTION ■REMOTE PERSONAL COMPUTER OPERATION CONNECTION ■GOT Mobile CONNECTION ■VNC(R) SERVER CONNECTION ■VIDEO, HDMI, AND RGB CONNECTION ■PRINTER CONNECTION ■MULTIMEDIA CONNECTION ■RFID CONNECTION ■WIRELESS
Open the catalog to page 1Thank you for choosing Mitsubishi Graphic Operation Terminal (Mitsubishi GOT). Read this manual and make sure you understand the functions and performance of the GOT thoroughly in advance to ensure correct use. • SAFETY PRECAUTIONS • (Always read these precautions before using this equipment.) Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly. The precautions given in this manual are concerned with this product. In this manual, the safety precautions are ranked as...
Open the catalog to page 3AWARNING When the GOT backlight has a failure, the GOT status will be as follows. Failure to observe this instruction may result in an accident due to incorrect output or malfunction. • GT27, GT25, GT23 The POWER LED blinks (orange/blue), the display section dims, and inputs by a touch switch are disabled. • GT2105-Q The POWER LED blinks (orange/blue), and the display section dims. However, inputs by a touch switch are still available. • GT2107, GT2104-R, GT2104-P, GT2103-P The display section dims. However, inputs by a touch switch are still available. Even if the display section dims,...
Open the catalog to page 4[DESIGN PRECAUTIONS] CAUTION Do not bundle the control and communication cables with main-circuit, power or other wiring. Run the above cables separately from such wiring and keep them a minimum of 100mm apart. Not doing so noise can cause a malfunction. Do not press the GOT display section with a pointed material as a pen or driver. Doing so can result in a damage or failure of the display section. When the GOT connects to an Ethernet network, the IP address setting is restricted according to the system configuration. • GT27,GT25,GT23 When a GOT2000 series model and a GOT1000 series model...
Open the catalog to page 5[MOUNTING PRECAUTIONS] CAUTION Use the GOT in the environment that satisfies the general specifications described in this manual. Not doing so can cause an electric shock, fire, malfunction or product damage or deterioration. When mounting the GOT to the control panel, tighten the mounting screws in the specified torque range with a Phillips-head screwdriver No. 2. • GT27, GT2512, GT2510, GT2508, GT23, GT2107 Specified torque range (0.36 N•m to 0.48 N•m) • GT2505, GT2105-Q Specified torque range (0.30 N•m to 0.50 N•m) • GT2104-R, GT2104-P, GT2103-P Specified torque range (0.20 N•m to 0.25...
Open the catalog to page 6[MOUNTING PRECAUTIONS] CAUTION For GT2512F-S, GT2510F-V, and GT2508F-V, attach an environmental protection sheet dedicated to the open frame model (sold separately) to the display section. Or, attach a user-prepared environmental protection sheet. Not doing so may damage or soil the GOT or cause foreign matter to enter the GOT, resulting in a failure or malfunction. When installing the supplied fittings on GT2512F-S, GT2510F-V, or GT2508F-V, tighten screws in the specified torque range (0.8 N•m to 1.0 N•m). Meld studs on the control panel to fasten the fittings. The studs must have strength...
Open the catalog to page 7[WIRING PRECAUTIONS] CAUTION When grounding the FG terminal and LG terminal of the GOT power supply section, note the following points. Not doing so may cause an electric shock or malfunction. • GT27, GT25, GT23, GT2107, GT2105-Q Make sure to ground the FG terminal and LG terminal of the GOT power supply section solely for the GOT (ground resistance: 100 Ω or less, ground cable diameter: 1.6 mm or more). (GT2107 and GT2105-Q do not have the LG terminal.) • GT2104-R, GT2104-P, GT2103-P Make sure to ground the FG terminal of the GOT power supply section with a ground resistance of 100 Ω or...
Open the catalog to page 8[WIRING PRECAUTIONS] CAUTION Plug the QnA/ACPU/Motion controller(A series) bus connection cable by inserting it into the connector of the connected unit until it "clicks". After plugging, check that it has been inserted snugly. Not doing so can cause a malfunction due to a contact fault. (GT27, GT25 Only) [TEST OPERATION PRECAUTIONS] WARNING Before testing the operation of a user-created monitor screen (such as turning on or off a bit device, changing the current value of a word device, changing the set value or current value of a timer or counter, and changing the current value of a buffer...
Open the catalog to page 9[STARTUP/MAINTENANCE PRECAUTIONS] CAUTION Do not disassemble or modify the unit. Doing so can cause a failure, malfunction, injury or fire. Do not touch the conductive and electronic parts of the unit directly. Doing so can cause a unit malfunction or failure. The cables connected to the unit must be run in ducts or clamped. Not doing so can cause the unit or cable to be damaged due to the dangling, motion or accidental pulling of the cables or can cause a malfunction due to a cable connection fault. When unplugging the cable connected to the unit, do not hold and pull from the cable...
Open the catalog to page 10[TOUCH PANEL PRECAUTIONS] CAUTION For the analog-resistive film type touch panels, normally the adjustment is not required. However, the difference between a touched position and the object position may occur as the period of use elapses. When any difference between a touched position and the object position occurs, execute the touch panel calibration. When any difference between a touched position and the object position occurs, other object may be activated. This may cause an unexpected operation due to incorrect output or malfunction. [PRECAUTIONS WHEN THE DATA STORAGE IS IN USE] WARNING...
Open the catalog to page 11All Mitsubishi Electric Europe B.V. catalogs and technical brochures
-
MELFA FAMILY Industrial robots
75 Pages
-
Product catalogue Compact PLC
130 Pages
-
Frequency inverter - FR-A800
4 Pages
-
Monitoring software - GT SoftGOT
87 Pages
-
MELSERVO J5 Serie Broschüre englisch
270 Pages
-
MELSERVO JET series Brochure en
160 Pages
-
SCARA robot - RH series
4 Pages
-
Frequency inverter - FR-A741
4 Pages
-
Frequency inverter - FR-D700
4 Pages
-
MELFA-FAMILY
64 Pages
-
Frequency inverter - FR-F800
4 Pages
-
LVS-FAMILY
152 Pages
-
Frequency inverter - FR-E700
4 Pages
-
Power contactor - MS-T/N
150 Pages
-
Monitoring software - GT SoftGOT
87 Pages
-
Contactor Relay - SR-T5
152 Pages