340 Route 16B • Center Ossipee, NH 03814 800-543-3580 • 603-539-4538 • Fax: 603-539-2183 MiteeBite.com Heavy-Duty™ T-Slot Instructions The Heavy Duty™ T-Slot clamp is intended for mounting to T-Slot tables with the three provided t-nuts and mounting screws. Each t-nut is coated with our Tungsten Carbide coating for added friction. The HD T-Slot clamp is designed be used with any of our large M12 Pitbull® Clamps (12,000 lbs/50,000 N.) or OK-VISE® DK model clamps (20,000 lbs/89,000 N.). C’bore for M12 SHCS Drive Screw Through Hole PROPER USE: 1. Hand tighten two rear mounting screws and clamp screw just until t-nuts are floating in t-slot 2. Slide clamp up to workpiece 3. Tighten two rear mounting screws 110 Ft/Lbs (150 N.m.) maximum 4. Tighten clamp to hold part 110 Ft/Lbs (150 N.m.) maximum INCLUDED HARDWARE FOR SPECIFIED ASSEMBLY : COMPATIBLE CLAMPS (3) 16mm t-nuts with Tungsten Carbide Coating medium grit (2) M12X35mm SHCS for t-nuts (1) M12X45mm SHCS clamp screw for use with Pitbull® (1) M12X40mm SHCS for use with single wedge OK-Vise® (1) M12X50mm SHCS for use with double wedge OK-Vise® NOTE: Clamp contact surfaces have option of application of Texture Grip Tungsten Carbide Coating. For more information, search “Tungsten Carbide” on our website - MiteeBite.com. REPLACEMENT T-NUTS Part No. Description 47131 OK-Vise® Clamp Model DK2-VT with Serrated Jaws 47132 OK-Vise® Clamp Model DK2-VT-S with Smooth Jaws 47141 OK-Vise® Clamp Model DK2-VT+5S with Machinable & Smooth Jaw 47144 OK-Vise® Clamp Model DK2-VT-TS with Tapped Holes & Smooth Jaw 47147 OK-Vise® Clamp Model DK2-VT-RS with Serrated Jaw & Smooth Jaw 47151 OK-Vise® Clamp Model DK2-WT Double Wedge with Serrated Jaws 47189 OK-Vise® Clamp Model DK2-VT-B with Serrated Ball & Smooth Jaw 56080 Pitbull® Clamp Knife Edge Tool Steel (2/pk) 56085 Pitbull® Clamp Blunt Edge Tool Steel (2/pk) 56088 Pitbull® Clamp Machinable Tool Steel (2/pk) T-Slot Size 340 Route 16B • Center Ossipee, NH 03814 800-543-3580 • 603-539-4538 • Fax: 603-539-2183 MiteeBite.com Heavy-Duty™ T-Slot Instructions The Heavy Duty™ T-Slot clamp is intended for mounting to T-Slot tables with the three provided t-nuts and mounting screws. Each t-nut is coated with our Tungsten Carbide coating for added friction. The HD T-Slot clamp is designed be used with any of our large M12 Pitbull® Clamps (12,000 lbs/50,000 N.) or OK-VISE® DK model clamps (20,000 lbs/89,000 N.). C’bore for M12 SHCS Drive Screw Through Hole COMPATIBLE CLAMPS PROPER USE: 1. Hand tighten two rear mounting screws and clamp screw just until t-nuts are floating in t-slot 2. Slide clamp up to workpiece 3. Tighten two rear mounting screws 110 Ft/Lbs (150 N.m.) maximum 4. Tighten clamp to hold part 110 Ft/Lbs (150 N.m.) maximum INCLUDED HARDWARE FOR SPECIFIED ASSEMBLY : (3) 16mm t-nuts with Tungsten Carbide Coating medium grit (2) M12X35mm SHCS for t-nuts (1) M12X45mm SHCS clamp screw for use with Pitbull® (1) M12X40mm SHCS for use with single wedge OK-Vise® (1) M12X50mm SHCS for use with double wedge OK-Vise® 47131 OK-Vise® Clamp Model DK2-VT with Serrated Jaws 47132 OK-Vise® Clamp Model DK2-VT-S with Smooth Jaws 47141 OK-Vise® Clamp Model DK2-VT+5S with Machinable & Smooth Jaw 47144 OK-Vise® Clamp Model DK2-VT-TS with Tapped Holes & Smooth Jaw 47147 OK-Vise® Clamp Model DK2-VT-RS with Serrated Jaw & Smooth Jaw 47151 OK-Vise® Clamp Model DK2-WT Double Wedge with Serrated Jaws 47189 OK-Vise® Clamp Model DK2-VT-B with Serrated Ball & Smooth Jaw NOTE: Clamp contact surfaces have option of application of Texture Grip Tungsten Carbide Coating. For more information, search “Tungsten Carbide” on our website - MiteeBite.com. REPLACEMENT T-NUTS 56080 Pitbull® Clamp Knife Edge Tool Steel (2/pk) 56085 Pitbull® Clamp Blunt Edge Tool Steel (2/pk) 56088 Pitbull® Clamp Machinable Tool Steel (2/pk) T-Slot Size