Extract from our online catalogue: pico+ ultrasonic sensors Current to: 2025-07-08 microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E [email protected] microsonic® is a registered trademark of microsonic GmbH. All rights reserved.

pico+ the "little guy" that can do it all: 4 ranges, 3 output signals, 2 housing variants and lO-Link interface. > Variant with 90° angled head > IO-Link interface > for support of the new industry standard > Automatic synchronisation and multiplex operation > for simultaneous operation of up to ten sensors in close quarters > UL Listed to Canadian and US safety standards > Improved temperature compensation > adjustment to working conditions within 120 seconds > Smart Sensor Profiles > more transparency between IO-Link Devices > 1 Push-Pull switching output > pnp or npn basis > 4 detection ranges...

Description The pico+ ultrasonic sensors are a compact series with M18 threaded sleeves and a housing length of only 41 mm. In addition to the variants with an axial beam direction, there is also a housing variant with a 90° angled head and radial beam direction. With four detection ranges from 20 mm to 1.3 m and three different output stages, this sensor family covers a wide range of applications. Sensors with the Push-Pull output stage support SIO and IO link modes. Sensors with analogue output are optionally available with 4–20 mA current output or 0–10 V voltage output. In SIO mode, sensors...

Teach-in of a switching point Teach-in of a two-way reflective barrier with a fixed reflector Apply +UB to pin 5 for about 3 seconds Then apply +UB to pin 5 again for about 10 seconds Teach-in of a two-way reflective barrier Place object at the near edge of the window (1) Apply +UB to pin 5 for about 3 seconds Then move the object to the far edge of the window (2) Then apply +UB to pin 5 again for about 1 seconds

Teach-in of an analogue characteristic or a window with two switching points NCC/NOC and rising/falling analogue characteristic curve can also be set via pin 5. One green and one yellow LED indicate the state of the output and support microsonic Teach-in. LinkControl optionally permits the extensive parameterisation of pico+ sensors. The LCA-2 LinkControl adapter , which is available as an accessory, can be used to connect pico+ sensors to the PC. Sensor connected to the PC via LCA-2 for programming Easy to synchronise A number of pico+ sensors can be run closely packed in applications synchronised...

If more than 10 sensors must be synchronised, this can be carried out with the SyncBox1 , which is available as an accessory. In instances of where a number of sensors are run at an IO-Link master, then the master's function is to assume synchronisation. Synchronised sensor cell in glass bottle production Updated to IO-Link version 1.1 The pico+ sensors with the extension „/A” in the order name are updated to IO-Link version 1.1 and support the Smart Sensor Profile. Please note that these sensor with the updated IO-Link version do not support IO-Link version 1.0 any longer. For example, when replacing...

scale drawing measuring range design operating mode particularities ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range resolution reproducibility accuracy analogue distance measurements narrow sound field UL Listed echo propagation time measurement ± 1 % (temperature drift internally compensated) operating voltage UB 10 - 30 V d.c., reverse polarity protection type of connection 5-pin M12 initiator plug

output 1 analogue output current: 4-20 mA switchable rising/falling delay prior to availability < 300 ms inputs synchronisation input teach-in input ultrasonic transducer max. tightening torque of nuts class of protection to EN 60529 operating temperature storage temperature weight further versions further versions technical features/characteristics temperature compensation controls brass sleeve, nickel-plated, plastic parts, PBT polyurethane foam, epoxy resin with glass contents 15 Nm IP 67 Teach-in via com input on pin 5 LCA-2 with LinkControl 1 x LED green: working, 1 x LED yellow: switch...

The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features. pico+ ultrasonic sensors

measuring range design operating mode particularities ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range resolution reproducibility accuracy analogue distance measurements 90° angular head narrow sound field UL Listed echo propagation time measurement ± 1 % (temperature drift internally compensated) operating voltage UB 10 - 30 V d.c., reverse polarity protection type of connection 5-pin M12 initiator plug

output 1 analogue output current: 4-20 mA switchable rising/falling delay prior to availability < 300 ms inputs synchronisation input teach-in input ultrasonic transducer max. tightening torque of nuts class of protection to EN 60529 operating temperature storage temperature weight further versions further versions technical features/characteristics temperature compensation controls brass sleeve, nickel-plated, plastic parts, PBT polyurethane foam, epoxy resin with glass contents 15 Nm IP 67 Teach-in via com input on pin 5 LCA-2 with LinkControl 1 x LED green: working, 1 x LED yellow: switch...

The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features. pico+ ultrasonic sensors

scale drawing measuring range design operating mode particularities ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range resolution reproducibility accuracy analogue distance measurements narrow sound field UL Listed echo propagation time measurement ± 1 % (temperature drift internally compensated) operating voltage UB 15 V bis 30 V DC, verpolfest type of connection 5-pin M12 initiator plug