Extract from our online catalogue: nano ultrasonic sensors Current to: 2025-01-27 microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E [email protected] microsonic® is a registered trademark of microsonic GmbH. All rights reserved.

nano - what's in a name? At just 55 mm long, including plug, the nano is the shortest M12 ultrasonic sensor on the market. > Ultrasonic sensor in the M12 threaded sleeve > IO-Link interface > for support of the new industry standard > The total length including plug is only 55 mm > Improved temperature compensation > adjustment to working conditions within 45 seconds > UL Listed to Canadian and US safety standards > 1 Push-Pull switching output > pnp or npn basis > 2 detection ranges with a measurement range of 20 mm to 350 mm > Operating voltage 10-30 V > for use with various voltage networks...

Description With a housing length of only 55 mm nano sensors with switching outputs are the smallest ultrasonic sensors inside the M12 threaded sleeve on the market. Analogue sensors are 60 mm long. nano has a 4-pole M12 circular plug and are taught via pin 2. For the nano sensor family there are 2 output stages and 2 measuring ranges available: 1 Push-Pull-switching output, in pnp or npn circuitry with IO-Link interface The temperature compensation of the sensors profits from a significant improvement. The sensors reach their operating point only 45 seconds after activation of the operating voltage....

> Place object (1) to be detected at the desired distance > Apply +Ub to pin 2 for about 3 seconds > Then apply +Ub to pin 2 again for about 1 second with a fixed mounted reflector. > Apply +Ub to pin 2 for about 3 seconds > Then apply +Ub to pin 2 again for about 10 second Teach-in of a two-way reflective barrier > Place object to the sensor-close window limit (1) > Apply +Ub to pin 2 for about 3 seconds until both LEDs flash > Then move the object to the sensor-distant window limit (2) > Then apply +Ub to pin 2 again for about 1 second until LED2 extinguishes > initially position the object...

Apply +UB to pin 2 for about 3 seconds until both LEDs flash Move the object to the sensor-distant window limit (2) Then apply +UB to pin 2 again for about 1 second Teach-in of an analogue characteristic or of a window with two switching points NCC/NOC and rising/falling analoge characteristic can also be set via pin 2. One green and one yellow LED indicate the state of the output and support microsonic Teach-in. IO-Link integrated in version 1.1.2 for sensors with Push-Pull output. The nano-15/CF and nano-24/CF support the Smart Sensor Profile, which creates more transparency between IO-Link devices....

scale drawing 1 x Push-Pull measuring range design operating mode ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range resolution reproducibility accuracy proximity switch/reflective mode reflective barrier window mode narrow sound field IO-Link version 1.1 Smart Sensor Profile UL Listed echo propagation time measurement ± 1 % (temperature drift internally compensated) operating voltage UB 10 - 30 V d.c., reverse polarity protection type of connection 4-pin M12 initiator plug

output 1 switching output Push-Pull, Ub-3 V, -Ub+3 V,Imax = 100 mA NOC/NCC adjustable, short-circuit-proof delay prior to availability < 300 ms synchronisation input teach-in input IO-Link product name product ID SIO mode support COM mode min. cycle time format of process data content of process data ISDU paramter system commands Smart Sensor Profile IODD version ultrasonic transducer operating temperature storage temperature Bit 0: initial state Pin 4; Bit 8-15: scale (Int. 8); Bit 16-31: measured value (Int. 16) Identification, measuring configuration, switched output, filter, temperature compensation,...

technical features/characteristics scope for settings Teach-in via com input on pin 2 LCA-2 with LinkControl lO-Link indicators LED grun, LED gelb narrow sound field lO-Link version 1.1 Smart Sensor Profile UL Listed The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features. nano ultrasonic sensors

scale drawing measuring range design operating mode particularities ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range reproducibility accuracy analogue distance measurements narrow sound field UL Listed echo propagation time measurement ± 1 % (temperature drift internally compensated) operating voltage UB 10 - 30 V d.c., reverse polarity protection type of connection 4-pin M12 initiator plug

output 1 analogue output current: 4-20 mA switchable rising/falling delay prior to availability < 300 ms inputs input 1 Teach-in input ultrasonic transducer operating temperature storage temperature brass sleeve, nickel-plated, plastic parts, PBT polyurethane foam, epoxy resin with glass contents IP 67 technical features/characteristics scope for settings Teach-in indicators 1 x LED green: working, 1 x LED yellow: object in the window particularities narrow sound field The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive...

scale drawing measuring range design operating mode particularities ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range reproducibility accuracy analogue distance measurements narrow sound field UL Listed echo propagation time measurement ± 1 % (temperature drift internally compensated) operating voltage UB 15 V bis 30 V DC, verpolfest type of connection 4-pin M12 initiator plug

output 1 analogue output voltage: 0-10 V (at UB > 15 V), short-circuit-proof switchable rising/falling delay prior to availability < 300 ms input 1 Teach-in input ultrasonic transducer operating temperature storage temperature brass sleeve, nickel-plated, plastic parts, PBT polyurethane foam, epoxy resin with glass contents IP 67 technical features/characteristics scope for settings Teach-in indicators 1 x LED green: working, 1 x LED yellow: object in the window particularities narrow sound field The content of this document is subject to technical changes. Specifications in this document are...