extract from our online catalogue: mic ultrasonic sensors current to: 2026-10-09 microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E [email protected] microsonic® ist eine eingetragene Marke der microsonic GmbH. Alle Rechte vorbehalten. Änderungen vorbehalten.

mic These completely metal mic sensors are available in two device designs with five different detection ranges. Highlights Basics > M30 housing and M12 circular connector in metal design > for harsh usage conditions > Automatic synchronisation > for simultaneous operation of up to ten sensors in close quarters > UL Listed to Canadian and US safety standards > 1 switching output in pnp variant > Analogue output 4-20 mA and 0-10 V > with automatic switching between current and voltage outputs > 5 detection ranges with a measurement range of 30 mm to 8 m > LinkControl > for configuration of sensors...

This very solid construction is fully made of metal from the M30 housing to the M12 circular connector. Since the sensors do not contain any operating elements or signal lamps, they are especially suited for application under extreme ambient conditions with high mechanical loads for housing and plug connector. The sensors are available in five detection ranges and cover a measuring range of 30 mm up to 8 m. M12 metal circular connector (left) and operation under rough conditions (right)

are available for all five detection ranges: > Single switching point > Two-way reflective barrier > Place object to be detected (1) at the desired distance > Apply +UB to pin 5 for about 3 seconds > Then apply +UB to pin 5 again for about 1 second Teach-in of a switching point D,"|ll)l)l), Reflector Teach-in of a two-way reflective barrier with a fixed reflector > Apply +UB to pin 5 for about 3 seconds > Then apply +UB to pin 5 again for about 10 seconds miCrOSOniC mic ultrasonic sensors

> Place object at the near edge of the window (1) > Apply +UB to pin 5 for about 3 seconds > Then move the object to the far edge of the window (2) > Then apply +UB to pin 5 again for about 1 second and rising/falling analogue characteristic curve can also be set via pin 5. Dll Teach-in of an analogue characteristic or a window with two Synchronisation using pin 5 switching points permits the simultaneous use of multiple mic sensors in an application. To avoid mutual interference, the sensors can be synchronised with one another. To do this, all the sensors are electrically connected on pin 5....

Sensor connected to the PC via LCA-2 for programming You have special requirements? Nothing as simple as that. With us, you can easily find an individual solution. Let us talk about your application: +49 231 97 51 51-82.

scale drawing scale drawing 1 x analogue 4-20 mA + 0-10 V operating mode analogue distance operating mode analogue distance metal plug for harsh opera- particularities tional conditions metal plug for harsh operational conditions Ultrasonic-Specific means of measurement echo propagation time means of measurement echo propagation time transducer frequency blind zone operating range max. range resolution reproducibility accuracy transducer frequency blind zone operating range max. range resolution reproducibility accuracy ± 1 % (temperature drift internally compensated) ± 1 % (temperature drift...

Electrical Data operating voltage UB 9 - 30 V d.c., reverse polarity type of connection 5-pin M12 initiator plug output 1 analogue output current: 4-20 mA / voltage: 0-10 V (at UB > 15 V), short-circuit-proof switchable rising/falling delay prior to availability < 390 ms teach-in input material brass sleeve, nickel-plated, ultrasonic transducer polyurethane foam, epoxy resin with glass contents further versions cable connection (on Technical Features/Characteristics controls com input<br/>control input scope for settings Teach-in via com input on Electrical Data operating voltage UB 9 - 30 V...

Accessories deployable accessory KST5A-2/M12 deployable accessory micro/omc mic ultrasonic sensors

scale drawing scale drawing 1 x analogue 4-20 mA + 0-10 V operating mode analogue distance operating mode analogue distance metal plug for harsh opera- particularities tional conditions metal plug for harsh operational conditions Ultrasonic-Specific means of measurement echo propagation time ding on the analogue window accuracy ± 1 % (temperature drift in ternally compensated) means of measurement echo propagation time ding on the analogue window accuracy ± 1 % (temperature drift in ternally compensated)

Electrical Data operating voltage UB 9 - 30 V d.c., reverse polarity type of connection 5-pin M12 initiator plug output 1 analogue output current: 4-20 mA / voltage: 0-10 V (at UB > 15 V), short-circuit-proof switchable rising/falling delay prior to availability < 440 ms teach-in input material brass sleeve, nickel-plated, ultrasonic transducer polyurethane foam, epoxy resin with glass contents further versions cable connection (on Technical Features/Characteristics controls com input<br/>control input scope for settings Teach-in via com input on Electrical Data operating voltage UB 9 - 30 V...

Accessories deployable accessory KST5A-2/M12 deployable accessory micro/omc mic ultrasonic sensors

scale drawing 1 x analogue 4-20 mA + 0-10 V operating mode analogue distance particularities metal plug for harsh opera tional conditions means of measurement echo propagation time ding on the analogue window operating mode proximity switch/reflective reflective barrier window mode particularities metal plug for harsh opera tional conditions means of measurement echo propagation time ± 1 % (temperature drift in- accuracy ternally compensated) ± 1 % (temperature drift internally compensated) miCrOSOniC mic ultrasonic sensors 13 / 27

Electrical Data operating voltage UB 9 - 30 V d.c., reverse polarity type of connection 5-pin M12 initiator plug output 1 analogue output current: 4-20 mA / voltage: 0-10 V (at UB > 15 V), short-circuit-proof switchable rising/falling delay prior to availability < 600 ms teach-in input material brass sleeve, nickel-plated, ultrasonic transducer polyurethane foam, epoxy resin with glass contents further versions cable connection (on Technical Features/Characteristics controls com input<br/>control input scope for settings Teach-in via com input on Electrical Data operating voltage UB 9 - 30 V...