Extract from our online catalogue: lpc+ ultrasonic sensors Current to: 2025-01-27 microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E [email protected] microsonic® is a registered trademark of microsonic GmbH. All rights reserved.

lpc+ well equipped: 2 Push-Pull switching outputs or 1 Push-Pull switching output with an analogue output in M18 housing. Analogue output 4–20 mA or 0–10 V plus 1 Push-Pull switching output in M18 design IO-Link interface Smart Sensor Profiles Improved temperature compensation UL Listed to Canadian and US safety standards for support of the new industry standard  more transparency between IO-Link Devices  adjustment to working conditions within 120 seconds 2 Push-Pull switching outputs 4 detection ranges with a measurement range of 20 mm to 1.3 m

Description The lpc+ ultrasonic sensors are optionally equipped with two Push-Pull switching outputs or an analogue output plus a Push-Pull switching output. The compact series with M18 threaded sleeves coves four detection ranges from 20 mm to 1.3 m. Ultrasonic sensors with the Push-Pull output stage support SIO and IO-Link modes. Sensors with analogue output are optionally available with 4–20 mA current output or 0–10 V voltage output. In SIO mode, sensors are configured using the microsonic Teach-in procedure on pin 5. For the lpc+ sensor family there are 2 output stages and 4 detection ranges...

Teach-in of a switching point Teach-in of a two-way reflective barrier with a fixed reflector Apply +UB to pin 2 for about 3 seconds Then apply +UB to pin 2 again for about 10 seconds Teach-in of a two-way reflective barrier Place object at the near edge of the window (1) Apply +UB to pin 5 for about 3 seconds Then move the object to the far edge of the window (2) Then apply +UB to pin 5 again for about 1 second Teach-in of an analogue characteristic or a window with two switching points NCC/NOC and rising/falling analogue characteristic curve can also be set via pin 5. One green and one yellow LED...

LinkControl optionally permits the extensive parameterisation of lpc+ sensors. The LCA-2 LinkControl adapter , which is available as an accessory, can be used to connect lpc+ sensors to the PC. Sensor connected to the PC via LCA-2 for programming Easy to synchronise A number of lpc+ ultrasonic sensors can be run closely packed in applications synchronised to stop them from influencing one another. To this end, the sync mode has to be activated and all the sensors are to be electrically connected one to another with pin 5. IO-Link integrated in version 1.1. The lpc+ ultrasonic sensors are equipped...

scale drawing operating mode lO-Link proximity switch/reflective mode reflective barrier window mode particularities IO-Link ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range resolution reproducibility accuracy echo propagation time measurement ± 1 % (temperature drift internally compensated) electrical data operating voltage UB 10 - 30 V d.c., reverse polarity protection no-load current consumption < 50 mA type of connection 5-pin M12 initiator plug

outputs output 1output 2 switching hysteresis switching frequency response time delay prior to availability switching output Push-Pull, Ub-3 V, -Ub+3 V,Imax = 100 mA NOC/NCC adjustable, short-circuit-proof switching output Push-Pull, Ub-3 V, -Ub+3 V,Imax = 100 mA NOC/NCC adjustable, short-circuit-proof inputs input 1 com input synchronisation input teach-in input IO-Link product name product ID SIO mode support COM mode min. cycle time format of process data content of process data system commands Smart Sensor Profile IODD version Bit 0: initial state Pin 4; Bit 1: initial state Pin 2; Bit 8-15:...

brass sleeve, nickel-plated, plastic parts, PBT, PA ultrasonic transducer polyurethane foam, epoxy resin with glass contents operating temperature storage temperature further versions further versions technical features/characteristics temperature compensation Teach-in via com input on pin 5 LCA-2 with LinkControl IO-Link The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features. lpc+ ultrasonic senso

scale drawing detection zone 2 x Push-Pull measuring range design operating mode ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range resolution reproducibility accuracy proximity switch/reflective mode reflective barrier window mode Smart Sensor Profile UL Listed echo propagation time measurement ± 1 % (temperature drift internally compensated) operating voltage UB 10 - 30 V d.c., reverse polarity protection type of connection 5-pin M12 initiator plug

switching output Push-Pull, UB-3 V, -UB+3 V,Imax = 100 mA NOC/NCC adjustable, short-circuit-proof switching output Push-Pull, UB-3 V, -UB+3 V,Imax = 100 mA NOC/NCC adjustable, short-circuit-proof switching hysteresis switching frequency response time delay prior to availability com input synchronisation input teach-in input IO-Link product name format of process data content of process data Bit 0: initial state Pin 4; Bit 1: initial state Pin 2; Bit 8-15: scale (Int. 8); Bit 16 -31: measured value (Int. 16) ISDU paramter Identification, measuring configuration, switched output, filter, temperature...

lpc+15/WK/CFF technical features/characteristics temperature compensation Teach-in via com input on pin 5 LCA-2 with LinkControl IO-Link 90°-Winkelkopf IO-Link Smart Sensor Profile UL Listed The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features. lpc+ ultrasonic sensors

measuring range designoperating mode particularities 20 - 250 mm cylindrical M18 lO-Link proximity switch/reflective mode reflective barrier window mode analogue distance measurement Smart Sensor Profile ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range reproducibility accuracy echo propagation time measurement ± 1 % (temperature drift internally compensated) electrical data operating voltage UB 10 - 30 V d.c., reverse polarity protection type of connection 5-pin M12 initiator plug micro/onic ipc+ ultrasonic sensors