Extract from our online catalogue: hps+ ultrasonic sensors Current to: 2025-01-27 microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E [email protected] microsonic® is a registered trademark of microsonic GmbH. All rights reserved.

hps+ in safety gear - When you need chemically resistant, pressure-resistant sensors. > Optionally used in normal pressure or overpressure > PTFE membrane > for protection against aggressive media > Stainless-steel or optional PVDF housing for hps+340 > for use in the food industry > Sealed against the housing with an O-ring made from FFKM > for the highest possible chemical resistance > Digital display with direct measured value output in mm/cm or % > Numeric configuration of the sensor using digital display > UL Listed to Canadian and US safety standards > 2 switching outputs in pnp variant...

Description For fill level measurements of aggressive media and in overpressure the ultrasonic transducers of the new hps+ sensors are now fitted out - as standard - with a PTFE film. It is sealed with a FFKM O-ring against the housing made of 1.4571 stainless steel or PVDF. This ensures a high degree of resistance to aggressive media. Fill level measurement in tanks The hps+ sensors can be used for fill level measurement under normal pressure or in tanks and containers with an overpressure of up to 6 bar. Its special software filters also allow its use in containers filled from above or that have...

2 switching outputs in pnp switching technology 1 analogue output with an additional pnp switching output The hps+ sensors with switching output have three operating modes:  Single switching point Two-way reflective barrier Window mode Two three-colour LEDs always show the current state of the switching outputs or the analogue output. With TouchControl all configuration can be done right at the sensor. The easily legible three-digit LED display continually shows the current distance value and automatically switches between millimetre and centimetre displays. Setting a switching or analogue output...

detection zone scale drawing design process connection G1 operating mode proximity switch/reflective mode reflective barrier window mode particularities druckfest bis 6 bar Uberdruck hohe Chemiebestandigkeit ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range by normal pressure maximum range by > 2 bar overpressure accuracy echo propagation time measurement ± 1 % (temperature drift internally compensated)

electrical data operating voltage UB 9 - 30 V d.c., reverse polarity protection no-load current consumption < 80 mA type of connection 5-pin M12 initiator plug hps+ ultrasonic sensors

output 1 switching output NOC/NCC adjustable, short-circuit-proof output 2 switching output NOC/NCC adjustable, short-circuit-proof delay prior to availability < 300 ms synchronisation input ultrasonic transducer operating temperature storage temperature stainless steel, plastic parts: PBT, TPU coated with PTFE film, FFKM O-ring IP 67 technical features/characteristics controls 2 push-buttons + LED display (TouchControl) scope for settings Teach-in and numeric configuration via TouchControl indicators 3-digit LED display, 2 x three-colour LED particularities druckfest bis 6 bar Uberdruck hohe...

The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features. hps+ ultrasonic sensors

detection zone measuring range operating mode proximity switch/reflective mode reflective barrier window mode analogue distance measurement druckfest bis 6 bar Überdruck hohe Chemiebeständigkeit Edelstahlausführung Display Prozessanschluss G1 UL Listed ultrasonic-specific means of measurement echo propagation time measurement transducer frequency blind zone operating range maximum range by normal pressure maximum range by ≥ 2 bar overpressure 0.025 mm to 0.30 mm, depending on the analogue window ± 1 % (temperature drift internally compensated)

electrical data operating voltage UB 9 - 30 V d.c., reverse polarity protection no-load current consumption < 80 mA type of connection 5-pin M12 initiator plug hps+ ultrasonic sensors

output 1 analogue output current: 4-20 mA / voltage: 0-10 V, short-circuit-proof switchable rising/falling output 2 switching output NOC/NCC adjustable, short-circuit-proof delay prior to availability < 300 ms synchronisation input ultrasonic transducer operating temperature storage temperature stainless steel, plastic parts: PBT, TPU coated with PTFE film, FFKM O-ring IP 67 technical features/characteristics controls 2 push-buttons + LED display (TouchControl) scope for settings Teach-in and numeric configuration via TouchControl indicators 3-digit LED display, 2 x three-colour LED particularities...

The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features. hps+ ultrasonic sensors

detection zone scale drawing design process connection G1 operating mode proximity switch/reflective mode reflective barrier window mode particularities druckfest bis 6 bar Uberdruck hohe Chemiebestandigkeit ultrasonic-specific means of measurement transducer frequency blind zone operating range maximum range by normal pressure maximum range by > 2 bar overpressure echo propagation time measurement 0.18 mm to 0.45 mm, depending on the analogue window ± 0.15 % ± 1 % (temperature drift internally compensated)

electrical data operating voltage UB 9 - 30 V d.c., reverse polarity protection no-load current consumption < 80 mA type of connection 5-pin M12 initiator plug hps+ ultrasonic sensors

output 1 switching output NOC/NCC adjustable, short-circuit-proof output 2 switching output NOC/NCC adjustable, short-circuit-proof delay prior to availability < 300 ms synchronisation input ultrasonic transducer operating temperature storage temperature stainless steel, plastic parts: PBT, TPU coated with PTFE film, FFKM O-ring IP 67 technical features/characteristics controls 2 push-buttons + LED display (TouchControl) scope for settings Teach-in and numeric configuration via TouchControl indicators 3-digit LED display, 2 x three-colour LED particularities druckfest bis 6 bar Uberdruck hohe...