Catalog excerpts
Product Specification Description The MICO Electrohydraulic (EH) wireless CAN interfaces with the MOBEUS ABS/TC/ESC ECU (Electronic Control Unit) utilizing a CAN-Bluetooth connection to the MOBEUS Service & Diagnostic Tool LINC. The MICO MOBEUS EH Wireless CAN interface is designed for use with MICO EH braking systems in Off-Highway vehicles and is fully compatible with the SAE J1939 CAN Communication standard. The result is a CAN interface that can communicate with MICO MOBEUS LINC (Single Mode), as well as other vehicle controls utilizing the vehicles CAN (Bridge Mode). The EH Wireless CAN interface provides an alternative to standard wired USB/CAN adaptors. It allows the wireless access to CAN systems using the standard Bluetooth interface provided with many notebooks (single mode). It has up to 100m transmission range (single mode) and up to 300m in bridge mode, the system allows CAN monitoring and data logging outside the vehicle during tuning and diagnostics. Multiple operating modes and simplified wireless system communication make this interface a valuable tool for vehicle tuning, diagnostic, and start-up. MICO is a trademark and registered trademark of MICO, Inc. MICO is registered in the U. S. Patent and Trademark Office as well as in Australia, Canada, Indonesia, Japan, Peoples Republic of China, South Korea, and the European Community. MICO, Incorporated Innovative Braking and Controls Worldwide MICO Form No. 89-950-012
Open the catalog to page 1Wireless CAN CAN Interfaces ISO 11898-2 bus coupling, up to 1 MBit System Data Voltage Supply: 9-30 Vdc maximum input range Current requirements: typically 50 mA at 12Vdc Physical Characteristics Connector: 9-pin sub-D plug for CAN External antenna version: RP-SMA connector, max antenna gain 3.4 dBi Bluetooth qualification: 2.1 + EDR Maximal Distance between devices: 100m (single mode), 300m (bridge mode) Chassis: IP 20 Weight: approximately 83g (0.18 lb) EMC, Environmental requirements CAN interface isolation working voltage: 130 V AC/DC (continuous), 1000 V DC (1second) Relative Humidity:...
Open the catalog to page 2Wireless CAN Power Supply X1 (PWR) X 1 Pin No. Signal CAN bus plug X2 (CAN) X 2 Pin No. Signal 1 2 CAN-L 3 GROUND 4 5 6 7 CAN-H 8 9 Push Button Pushbutton Descriptions Restore factory settings Not used No Bluetooth MAC address is stored in the configuration of the device, and there is no connection to an SPP server on the unit CAN Flashing green Flashing red Steady red A CAN message has been sent or received and the CAN controller is not in the warning state. A CAN message has been sent or received and the CAN controller is in the warning state The CAN controller is in the BUS-OFF state...
Open the catalog to page 3All MICO catalogs and technical brochures
-
Brake Lock Application Guide
16 Pages
-
MICO Product Guide
20 Pages
-
Fluid Reservoirs
2 Pages
-
PRESSURE LIMITER
2 Pages
-
Hydraulic Brake Valves Catalog
64 Pages
-
Check Valve Assembly
2 Pages
-
Heavy-Duty Ratchet Handle
2 Pages
-
MICO CAN-bus Keypads
6 Pages
-
MOBEUS
4 Pages
-
CUSTOM ENGINEERED SWITCHES
48 Pages
-
Load-Apportioning Valve
2 Pages
-
MICO Multiple Disc Brakes
51 Pages
-
Boosted Master Cylinders
27 Pages
-
Air/Hydraulic Actuators
22 Pages
-
Hydraulic Remote Actuators
27 Pages
-
Product Guide
20 Pages
-
MICO Boosted Master Cylinders
23 Pages
Archived catalogs
-
Caliper Disc Brakes Catalog
23 Pages
-
Electro-Hydraulic Components
15 Pages