ZR/ZG Pedestal Bearings
9Pages

{{requestButtons}}

Catalog excerpts

ZR/ZG Pedestal Bearings - 1

Miba Industrial Bearings Pedestal Bearing ZR / ZG

Open the catalog to page 1
ZR/ZG Pedestal Bearings - 2

The Industrial Bearing Branch of the Miba Bearing Group produces hydrodynamic bearings and labyrinth seals for use in mechanical and plant engineering which are used in a wide range of high-performance applications. Our highly inspired teams, work diligently to serve our customers the best bearing solutions for each and every application. Content Side Description of the pedestal design Radial bore profile selection Oil flow Bearing dimensions (ZR) Bearing dimensions (ZG) Dimensions of shaft Types and dimensions of seals Bearing types and designations Checklist Description of the pedestal...

Open the catalog to page 2
ZR/ZG Pedestal Bearings - 3

Oil supply Fully self-contained lubrication is achieved by using a loose oil ring. Alternatively, where bearings are lubricated by an external oil circulation system, this loose oil ring can be used to permit an emergency shutdown without damage in case an oil system failure occurs. Z-bearings can be used for marine applications, where an oil ring guide assures proper lubrication even if extreme vessel motions occur. Electrical insulation To prevent stray currents conducted by the shaft, Z-bearings can optionally be supplied electrically insulated. In this case, the spherical seat of the...

Open the catalog to page 3
ZR/ZG Pedestal Bearings - 4

ZD tilting Pads per size d4 = Earthing device or plug - Pg7 d5 = Oil inlet soil circulation or recirculating pump) d6 = Provision for thermometer G 1/2" d7 = Oil sight glass .or oil .outlet sail circulation'' d8 = Plug 'connectron for heater, oil sump thermometer, water cooler' t = Depth of thermometer bore Drawings shown here are for reference only. Some fin details, for example, may vary from size to size.

Open the catalog to page 4
ZR/ZG Pedestal Bearings - 5

ZD tilting pads per size d4 = Earthing device or plug - Pg7 d5 = Oil inlet (oil circulation or recirculating pump) d6 = Provision for thermometer G 1/2" d7 = Oil sight glass or oil outlet (oil circulation) d8 = Plug (connection for heater, oil sump thermometer, water cooler) t = Depth of thermometer bore 1) Bore for dowel pin 2) Details on request

Open the catalog to page 5
ZR/ZG Pedestal Bearings - 6

1) Limit dimensions of the shaft acc. DIN 31 698, form and positional tolerance and surfaces roughness acc. to DIN 31 699. 2) Standard thrust clearance is 0,6 mm. If reversible thrust loads or shock load occur, dimension b20 can be reduced by 0,3 mm. If a locating bearing (shell type B,K) is needed only for test runs, dimension b20 can be enlarged by 4 up to 6 mm. 3) If the non-locating bearing must allow larger motions (due to heat expansion or to large thrust clearances caused by the unit), dimension b21 can be enlarged. 4) The plunge cut d32 is dropped, if it is equal or smaller as the...

Open the catalog to page 6
ZR/ZG Pedestal Bearings - 7

1 // Types and dimensions of seals 1) These sizes of seals can be manufactured in floating labyrinth seal or rigid seal. All other seal sizes can only be manufactured in rigid seal. 2) Details on request. Rigid seal* (Protection IP 44) *Can be combined either with a bolt-on baffle (IP 55) or with a dust flinger (IP 54) Floating labyrinth seal with bolt-on baffle (Protection IP 55) Floating labyrinth seal with dust flinger (Protection IP 54) Special seal designs for specific applications upon request.

Open the catalog to page 7
ZR/ZG Pedestal Bearings - 8

1 // Type Z Plain bearing 2 // Housing R Pedestal bearing, finned G Pedestal bearing, smooth 3 // Heat dissipation N Naturally cooled by convection Z Lubrication by oil circulation with external oil cooling Lubrication by oil circulation with external oil cooling for X high oil throughput W Finned water cooler in the oil sump U Recirculating oil pump and natural cooling T Recirculating oil pump and water cooler in the oil sump Example of a bearing designation: Z R N L B - 35 - 300 Pedestal bearing, finned, naturally cooled by convection, plain cylindrical bore with loose oil ring, plain...

Open the catalog to page 8
ZR/ZG Pedestal Bearings - 9

+ Europe 2 sites North America 3 sites South America 1 site • Miba Industrial Bearings Contacts: Germany Miba Industrial Bearings Germany GmbH Robert-Bosch-Breite 10 C 37079 Gottingen, Germany MIBG_sales@miba.com Germany Miba Industrial Bearings Germany Osterode GmbH & Co. KG Rolandsweg 16-20 37520 Osterode, Germany MIBG_sales@miba.com USA Miba Industrial Bearings U.S. LLC 1111 Cedar Creek Rd, Grafton, WI 53024, USA MIBUSG_Sales@miba.com USA Miba Industrial Bearings U.S. LLC 3300 E 8th St. Columbus, NE 68601, USA MIBUSG_Sales@miba.com USA Miba Industrial Bearings U.S. (Houston) LLC 1800 W...

Open the catalog to page 9

All MIBA INDUSTRIAL BEARINGS catalogs and technical brochures