MPI-DN, MPI-D MULTICHANNEL ELECTRONIC RECORDER for HART or RS-485/ MODBUS RTU SENSORS            18 channels for HART / Modbus RTU sensors 2 digital channels 16 math channels 4 relay outputs for alarm or control functions 2 GB internal memory for advanced data recording color LCD TFT display USB port on the front panel with IP54 protection Ethernet port: Modbus TCP, Web Server RS 485 port: ASCII and Modbus RTU Dedicated software for visualization of measurement data Housing for panel mounting or wall mounting 20 CHANNEL FOR MEASURED PROCESS VALUES  18 channels designed to read data from sensors and instruments with digital protocol (HART or Modbus RTU).  2 digital inputs (PULS) for state, pulse or frequency measurements; OC, voltage or NAMUR configuration. HART  HART port with power supply for sensors (24 VDC /60 mA), up to 12 sensors in multidrop configuration.  Supported rev.4., rev.5., rev.6. Possible configuration as Primary or Secodary Master.  Read variables: PV - primary variable, SV – secondary variable, TV third variable, FV - fourth variable. MODBUS RTU (RS485 Port)  Sensors or instruments connected in parallel to one twisted pair of wires.  Baud rate from 1200 bps to 115200 bps.  Available functions: 03 (Read Holding Register) and 04 (Read Input Register), registers in the range 0 ... 65535.  Data format: unsigned integer, integer, unsigned long, unsigned long swapped, long, long swapped, floating point, floating point swapped. PULS INPUTS  Measurement frequency range 0.001 Hz to 10 kHz.  Pulse counting for totalisers.  Trac

MATH CHANNELS  16 math channels can display calculated result based on measured or calculated values.  Available functions: addition, subtraction, multiplication, division, square roots. ARCHIVING RESULTS  Writing to internal 2GB memory.  Text files format with the encrypted checksum, recording to one file (until end or overwrite) or to successive files (24H, week, month).  Recording time interval from 3 s to 24 h; possible to define two switched frequencies depending on alarm threshold state. 4 RELAY OUTPUTS, THRESHOLDS ALARM-CONTROL  4 solid-state relay outputs rated at 0,1 A / 60 V....

TECHNICAL DATA Type of display: Reading field size: Indication: Keyboard: FRONT PANEL Full color graphic TFT LCD, 272 x 480 px. 43.8 mm x 77.4 mm 3 two-color LEDs (green and red) MPI-D : Membrane, 7 buttons MPI-DN: Membrane, 19 buttons SERIAL PORT RS-485 (1) Transmission protocol Modbus RTU Transmission rate 3 s, 4 s, 5 s, 6 s, 10 s, 12 s, 15 s, 30 s, 1 min Baud rate 1.2, 2.4, 4.8, 9.6 ,19.2, 38,4, 57.6, 115.2 kbps Transmitter address space 1 … 247 Maximum load 32 receivers / transmitters Maximum line length 1200 m Galvanic separation Yes, 250 VAC / 300 VDC Maximum differential voltage A(+) –...

Number of outputs Type of outputs Maximum load current Maximum voltage Wire connection Number of outputs Output current range Maximum voltage beetwen I- and ILoop resistance (for Uloop_power = 24 V) Resolution of C/A converter Accuracy Current loop power Galvanic separation from power supply Wire connection 2,2 mA – 6,5 mA RELAY OUTPUTS 4 Solid-state relays 100 mA (AC/DC) 60 V (AC/DC) MPI-D: two 8-pin screw type terminal blocks, max. cable diameter 1,5 mm2 MPI-DN: spring type terminal block, cable diameter 0,2 mm2 – 1,5 mm2 ANALOG OUTPUT 4-20mA (optional) 1 4-20mA 28 VDC 0 … 500 Ω 16 bit 0.5%...

INTERNAL DATA MEMORY Capacity 2 GB (Flash type) Estimated recording time for recording speed every 3s for 16 approximately 400 days measuring channels Recording indication Green-red LED on the front panel Supply voltage Power consumption Wire connection POWER SUPPLY (MPI-D, MPI-DN) 24 VAC (+5% / -10%) 50/60 Hz 24 VDC (15 ... 30 VDC) (any polarity) 6 W max (power supply 24 VDC) 6 VA max (power supply 24 VAC) MPI-D: 3-pin screw type terminal block, max. cable diameter 1,5 mm2 MPI-DN: spring type terminal block, cable diameter 0,2 mm2 – 1,5 mm2 POWER SUPPLY (only MPI-DN) 100 … 240 VAC 50/60 Hz Max...