TXR, TXA
4Pages

Proximity Probe Transmitter Trendsetter Model TXR (Radial) and TXA (Axial) Specifications Unless otherwise noted, all specifications are specified at 21°C (70°F), +24 Vdc power supply, gap set to 1.27 mm (50 mils) and using Metrix AISI 4140 steel target. Operating Temperature Range: -40°C to 85°C (-40°F to 185°F) Operating Humidity Range: 95% non-condensing, external environmental protection is required This new Trendsetter transmitter is a 2-wire looppowered transmitter combining an eddy current probe driver and a signal conditioner in a single package. It provides a 4-20 mA output proportional to overall peak to peak displacement and operates with Metrix probes and extension cables as well as 4 major probe systems. A DC voltage output and dynamic signal is available at the BNC connector. The TXR Transmitter is designed for radial vibration while the TXA Transmitter is designed for axial position vibration. Features • Cost effective alternative to dedicated rack mount monitors • Loop-powered driver/transmitter • Compatible with 4 major probe systems • Easily factory calibrated to non-standard shaft material • DIN Rail mounting (flat mounting base available) (P/N 9647) • BNC for access to dynamic output and probe gap • PBT plastic material Machines using Shaft Monitoring • Oil lubricated fluid film bearing machines: -Centrifugal Pumps -Turbo Compressors -Steam and Gas Turbines -Large Fans and Blowers -Gear Box Shafts -Generators -Large Electric Motors Power Requirements: • 17 to 30 VDC with a maximum start up current of 23 mA (-40°C to 85°C) • Maximum loop resistance is determined by RL = 50 (Vs-17) ohms Frequency Response: • 5 Hz to 5 kHz +0, -3 dB pk-pk vibration • 0 Hz to 20 Hz +0, -3 dB position Linear Range: • 0.5 to 2.0 mm (20 to 80 mils); (8 mm probe) • 0.5 to 4.0 mm (20 to 160 mils); (11 mm probe) Buffered Output: • 7.87 V/mm (200 mV/mil) +/- 5% when calibrated as a system, +/- 12% including interchangeability error when measured in 0.25 mm (10 mils) increments over linear range • 3.94 V/mm (100 mV/mil) +/- 5% for 11 mm probes when calibrated as a system, +/- 12% including interchangeability error when measuredin 0.25 mm (10 mils) increments over the linear range • 0 Hz to 3 kHz +0, -3 dB Note: The buffered output is intended for local diagnostics only and will not support loads that are less than 100k ohms. 4-20 mA Output: • 4 mA +/- .1 mA with no input vibration • 4 mA +/- .2 mA @ -40°C to 85°C with no input vibration • 20 mA +/- .5 mA @ -40°C to 85°C with full scale input vibration • < 3.6 mA indicates “Not OK” condition

Proximity Probe Transmitter Trendsetter Model TXR (Radial) and TXA (Axial) Specifications (continued) Hazardous Area Ratings: • CSA Certified: Intrinsically Safe Class I, Div 1, Grps A, B, C & D, Temp Code T4. • CSA Certified: Non-Incendive ClassI, Div 2, Grps A, B, C & D • BASEEFA Certified: Intrinsically Safe Ex ia IIC T4, Non-Incendive Ex ia IIC T4 Weight & Dimensions Product Inputs: Trendsetter will support the following probes: • 10000 and 7200 series probes with 5, 8 or 11 mm tips and 5 or 9 meter system lengths • 3300 series probes with 5, 8 or 11 mm tips and 5 or 9 meter system...

Proximity Probe Transmitter ^^^^^M Trendsetter Model TXR (Radial) and TXA (Axial) Experience Value www.metrixvibration.com • info@metrixvibration.com • Tel: 281-940-1802 • Doc #1004209 Rev E • 07/13

^^^m Proximity Probe Transmitter Trendsetter Model TXR (Radial) and TXA (Axia Cross-Reference from 5465/5488 to Trendsetter TXR/TXA *For negative polarity, please add an "N" after the designated number for the Range. All systems calibrated to AISI 4140 steel target material. If probe target material varies from AISI 4140 please contact the factory for custom material calibration Experience Value www.metrixvibration.com • info@metrixvibration.com • Tel: 281-940-1802 • Doc #1004209 Rev E • 07/13