Fluidification bagging machine
8Pages

Ensacadoras.angl filmar 3-05 5/1/06 00:13 Página 4 PACK Air

Ensacadoras.angl filmar 3-05 5/1/06 00:13 Página 7 CKERS T he fluidisation process allows the filling of a wide range of fine-grain products, powder or a mixture of both in valve bags. The modular design enables us to comply with our customers’ requirements, which also provides the opportunity to select the number of nozzles according to the required capacity. By combining a low-pressure feed system that fluidises the lower section of the chamber with a second upper inlet will accelerate the product output, thus increasing installation performance. This range of bagging equipment comes...

Ensacadoras.angl filmar 3-05 5/1/06 00:13 Página 8 Air packers Characteristics • Air packers are used for low-fluidity products with either a fine or coarse structure and also for products that have a tendency to become agglomerated. • The type of construction employed facilitates the discharge of material because of the use of a vertical chamber and the inclined fluidised base makes for easy output flow as well as final cleaning. • The equipment does not include any rotating parts and therefore, there is virtually no wear and tear. • The products to be bagged are not crushed, separated,...

Ensacadoras.angl filmar 3-05 5/1/06 00:14 Página 11 Characteristics Air packers • An ultrasonic sealing system can be optionally installed and with this system, the bags emerge clean and without any product loss during transport. They are easily arranged on the pallet with a good quality layout finish, together with optimum pallet appearance. This type of sealing operation guarantees that the valve is watertight. • An optional inflatable sleeve can be installed on the nozzle in order to prevent the product from escaping through the bag valve during the filling operation, thus preventing...

Ensacadoras.angl filmar 3-05 5/1/06 01:11 Página 12 Air packers Operation T he machine is installed underneath a feed hopper equipped with level sensors. The product is fed into the fluidisation chamber through a large diameter butterfly valve, which will remain open until the necessary material level within the chamber has been reached. Once the intake valve closes, the bag-filling process commences, which is accomplished by producing over-pressure in the chamber, together with the fluidisation of the product. During the filling process, the equipment monitors the flow rate and...

Ensacadoras.angl filmar 3-05 5/1/06 00:14 Página 15 Operation Air packers 7

Ensacadoras.angl filmar 3-05 5/1/06 00:14 Página 16 Air packers Options A dditional fluidisation system at the filling pipe for difficult-to-handle products. Filler nozzle with inflatable sleeve. Air blowing system for cleaning the nozzle. Surface treatment using sand-blasting and epoxy paint, etc. Flame-proof construction. Protective cover for reducing noise from blower. Parts that come into contact with the product are made from: • Stainless steel. • Wear-resistant steel. The fluidisation chamber is made from: • Rubber for products that tend to bind together. • Stainless steel with a...

Ensacadoras.angl filmar 3-05 5/1/06 01:12 Página 19 Layout dimensions Air packers Ø355 2280 1 - Product accumulation hopper 836 2 - Sleeve 2610 2280 2610 Ø355 836 3 - Butterfly valve 4 - Packing machine body 5 - Level switch 6 - Lower cover 7 - Spout 3140 8 - Loading cell 1942 5730 9 - Dosing valve 3140 1942 General measurements made with belt conveyor below 5730 ground level 10 - Decompression valve 11 - Product 1550 1580 1550 850 730 850 730 10 1580 1 2 5 Ø355 3 Bags magazine 2750 8 1115 4 3080 Rocking arm applicator 11 Hopper and dust collection endless 3140 1942 5730 6 General...