Group: Messer Group
Catalog excerpts
STEEL MILL EQUIPMENT MESSER CUTTING SYSTEMS
Open the catalog to page 1HEAVY-DUTY HAND CUTTING TORCH SMB 600 With spring lever for cutting oxygen (version with hand wheel valve available upon request), for cutting of slabs, ingots, billets, non-alloy and low-alloy steel castings and forgings, and for cutting of steel scrap, Cutting range see table. Fuel gases: A = Acetylene PM = Propane, methane (natural gas) Y = Methyl acetylene propadien mixtures (MAPP a.o.) Hose connections according to EN 560, G 1/2“ RH-11 for oxygen and G 3/8“ LH-9 for fuel gas Operating data see pages 6 and 7 Heavy-duty hand cutting torch without accessories Version with angled torch...
Open the catalog to page 2SMB 600 / 663HEAVY-DUTY HAND CUTTING TORCHES Heavy-duty hand cutting torch without accessories Description Cutting range Art. No. Cat. No. Torch carriage Nozzle cleaners in case Hand wheel valve insert for cutting oxygen picture may differ I subject to change MESSER® Cutting Systems
Open the catalog to page 3SMB 600 PZFD torch length 1000 mm Execution with angled torch head and powder equipment complete incl. powder nozzle and 716.14180 * 006 quick action valve SMB 600 PZFD torch length 1500 mm Execution with angled torch head and powder equipment complete incl. powder nozzle and 716.14181 * 006 quick action valve MESSER® Cutting Systems * on request I picture may differ I subject to change SMB 600 / 663 | STEEL INDUSTRIES P.5
Open the catalog to page 4CUTTING NOZZLES GRICUT® 5310-A Cutting nozzle Cutting Inozzle CUTTING NOZZLES GRICUT® 5281-PMY ChUtt‘ng Art. No. thick- Cutting Heating ness Inozzle nozzle ,g The tables indicate standard values based on the use of plain steel with a carbon content of up to 0,3 % and oxygen with a minimum purity of 99.5 %. The allowable particle size in the oxygen is 30 pm maximum. The pressure stated are gauge pressure measured at the torch inlet. The consumption data indicated in m3/h apply to the standard condition as per DIN 1343. • Use only clean, undamaged nozzles. MESSER® Cutting Systems P.6 STEEL...
Open the catalog to page 5HEAVY-DUTY HAND CUTTING TORCHES 12,2 CUTTING NOZZLE GRICUT® CUTTING NOZZLE GRICUT® 5281-PMY MESSER® Cutting Systems $ on request I picture may differ I subject to change SMB 600 / 663 | STEEL INDUSTRIES P.7
Open the catalog to page 6SMB 663 with straight torch head HEAVY DUTY HAND CUTTING TORCH SMB 663 with spring lever for cutting oxygen (version with hand wheel valve available upon request), for cutting of slabs, ingots, billets, non-alloy and low-alloy steel castings and forgings, and for cutting of steel scrap. Cutting-range, see attached table. Fuel gas: A = Acetylene PM = Propane, methane (natural gas) Y = Methyl acetylene propadien mixtures (MAPP a.o.) Hose connections according to EN 560, G 1/2“ RH-11 for oxygen and G 3/8“ LH-9 for fuel gas Operating data see pages 11 and 12 SMB 663 Heavy-duty hand cutting...
Open the catalog to page 7SMB 600 / 663 HEAVY-DUTY HAND CUTTING TORCHES Torch head with skid Torch head with torch carriage Accessories Description Torch carriage Nozzle cleaners in case Hand wheel valve insert Torch head with powder nozzle Powder additional equipment Description Powder equipment complete incl. powder nozzle and quick action valve for torch length 1260 mm (SMB 663 only) Powder equipment complete incl. powder nozzle and quick action valve for torch length 1500 mm (SMB 663 only) Standard cutting nozzles are used Powder distributor P75 (see page 19) Inlet pressure 10 bar max., Container pressure 1.0...
Open the catalog to page 8Heavy-Duty Hand-Cutting-Torch SMB 600 completely with powder equipment Description Art.-No. Cat.-No. SMB 663 PZFD torch length 1260 mm Execution with angled torch head and powder equipment complete incl. powder nozzle and 716.14186 * 006 quick action valve SMB 663 PZFD torch length 1260 mm Execution with straight torch head and powder equipment complete incl. powder nozzle and 716.14188 * 006 quick action valve SMB 663 PZFD torch length 1500 mm Execution with angled torch head and powder equipment complete incl. powder nozzle and 716.14187 * 006 quick action valve SMB 663 PZFD torch length...
Open the catalog to page 9CUTTING NOZZLES DPC-A SMB 600 / 663HEAVY-DUTY HAND CUTTING TORCHES Cutting thickness [mm] MESSER® Cutting Systems % on request I picture may differ I subject to change SMB 600 / 663 | STEEL INDUSTRIES P.11
Open the catalog to page 10MESSER® Cutting Systems P.12 STEEL INDUSTRIES | SMB 600 / 663 * on request I picture may differ I subject to change
Open the catalog to page 11Cutting values for heavy duty hand torch type SMB 663 with Fe powder unit Oxygen purity: Test material: Fuel gas: Torch adjustment: Used powder: Cutting speed tolerances: Cut quality: Note: min. 99,5 % Stainless steel CrNi 18/8 N propane according to operating data for cutting nozzle type DBH-PMY (page 11-12) GRISINT® (Art. No. 0.462.004), the values are approximate approx. 20 % Oxyfuel hand cuts with FE powder addition depend heavily upon the skill of the operator. Without mechanical guidance only scrap quality can be achieved. All data and especially the low wear with powder nozzles and...
Open the catalog to page 12HEAVY-DUTY HAND CUTTING TORCHES on request picture may differ subject to cha
Open the catalog to page 13Sleeve for powder cutting nozzle Powder hand cutting torch AC 41 With spring lever valve for simultaneous control of oxygen and powder, for cutting of heat resistant stainless steel and high-carbon steels up to 300 mm, and for Non-ferrous materials and cast iron up to 150 mm material thickness. Fuel gas: acetylene or propane, methane (natural gas), Coal gas, MAPP. Hose connections acc. to DIN 8542: G 3/8“ RH-9 fuel gas G 3/8“ LH-9, powder G 1/4“ RH-6. Operating date see page 5 Powder cutting nozzle for propane, methane (natural gas), Coal gas, MApP MESSER® Cutting Systems $ on request I...
Open the catalog to page 141I Circle rod complete Torch carriage picture may differ I subject to change MESSER® Cutting Systems
Open the catalog to page 15POWDER HAND CUTTING TORCH AC 41 Material thickness [mm] The tables indicate standard values based on the use of plain steel with a carbon content of up to 0.3 % and oxygen with a minimum purity of 99.5 % and by use of GRISINT® Iron-powder. The allowable particle size in the oxygen is 30 pm maximum. The pressure stated are gauge pressure measured at the torch inlet. The consumption data indicated in m3/h apply to the standard condition as per DIN 1343. • Use only clean, undamaged nozzles. MESSER® Cutting Systems $ on request I picture may differ I subject to change
Open the catalog to page 16All MESSER CUTTING SYSTEMS catalogs and technical brochures
-
Flame Straightening
20 Pages
-
Oxyfuel Technology
193 Pages
-
OmniWin
11 Pages
-
OmniFab
9 Pages
-
LaserMat® II
4 Pages
-
Global ControlS
2 Pages
-
GLOBAL CONTROLPlus
2 Pages
-
Messer Cutting Systems
32 Pages
-
GRIFLAM®
118 Pages
-
MINITHERM®
28 Pages
-
ALFA
2 Pages
-
Safety Devices
2 Pages
-
Quicky®
2 Pages
-
MultiTherm
4 Pages
-
MultiTherm® Eco
4 Pages
-
Product Range
32 Pages
-
MetalMaster Xcel
4 Pages
-
Steel Mill Technology
36 Pages
-
Heating Technology
118 Pages
-
Drilling Unit
4 Pages
-
Torches & Nozzles
2 Pages
-
StableCut
1 Pages
-
Minitherm
28 Pages
-
Combination Torch Systems
4 Pages
-
PowerBlade®
4 Pages
-
OmniMat®
4 Pages
-
LaserMat II
4 Pages
Archived catalogs
-
Conveyor Belt Table
2 Pages
-
Сutting Tables
2 Pages
-
MetalMaster
4 Pages
-
GlobalControl S
2 Pages
-
GlobalControl Plus
2 Pages
-
Laser Bevel Head
2 Pages
-
Vibration Conveyor Table
2 Pages
-
Scraper Conveyor Table
2 Pages