SPTSM
9Pages

Catalog excerpts

Optical Kit Encoder Series SPTSM ■ Up to 1024 pulses / 360° ■ 2 channels + index pulse ■ Outputs TTL compatible or as option linedriver ■ Supply voltage 5 VDC ■ Applicable on different shaft diameters ■ Option: Housing with through hole for longer shafts ■ Only 17mm housing depth ■ Simple assembling thanks to optional assembling tools Universal optical kit encoder, quick and safe to install with optional mounting tools. Virtually no mechanical wear. Thanks to the option with bore hole in the housing cover, it is also suitable in conjunction with long shafts. Number of pulses Output channels Output electronics Supply voltage Current consumption (no load) Output voltage High @ IOH Output voltage Low @ IOL Max. output current per channel Limit frequency 50, 96, 100, 200, 256, 360, 400, 500, 512,1000, 1024 Imp./Rev. A, B, Z (Z not available for 96 Imp./Rev. and 1024 Imp./Rev.) TTL or as an option linedriver 5 VDC +/-10 % 2 channels A/B typ. 17 mA 3 channels A/B/Z typ. 57 mA Min. 2.4 V (2 channels A/B: IOH = -40 pA max., 3 channels A/B/Z: IOH = -200 pA max.) Max. 0.4 V (2 channels A/B: IOL = 3,2 mA, IOL 3 channels 3,86 mA) 5 mA 100 kHz Protection grade (IEC 60529): Ascertained in assembled condition (without solder or clamping terminals) Operating temperature range Storage temperature range Material housing Material encoder disc / hub Assembling parts: Included in delivery Not included in delivery Required assembling tools (not included in delivery): Assembling tools are mandatory for mounting the sensor in the application and they must be ordered separately Maximum permissible axial play Maximum permissible eccentricity Humidity Mass (product without option ST or N) IP 30 -20..+60 °C (other temperatures on request) -40 °C...+100 °C Thermoplastic Thermoplastic /aluminium 2 screws for fixing the housing cover are included in Screws for mounting the base plate are not included in delivery 1. Distance gauge: applicable for all shaft diameters 2. Centering gauge must be ordered according the shaft diameter +/-0,25 mm +/-0,02 mm 90 % RF no dewing ca. 25 g MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Date: 04/29/2021 Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ info@megatron.de Page: 1 of 9 Specifications are subject to change without not

Open the catalog to page 1

Series SPTSM Data Sheet for Angle SensorsOptical Kit Encoder Order Code 1.) Option BZ = 3 Channels: Track A, Track B, Track Z (One index impulse per 360° rotation) Option B = 2 Channels: Track A, Track B, without index impulse The number of pulses per revolution and the possible number of channels can not be chosen arbitrarily. For example it is not possible to get the optical resolution 1024ppr together with index track Z. 2.) This option is only available with minimum order quantity 3.) Optical resolution 100ppr in combination with 4mm shaft diameter is not coupled to a minimum order...

Open the catalog to page 2

Series SPTSM Data Sheet for Angle SensorsOptical Kit EncoderOrder example SPTSM Kit Encoder: Requirement: Applicable for shaft diameter 0 6.00 mm, optical resolution 512 impulses per revolution, 3 channels (A/B and index), electrical output: TTL, without through bore in housing cover, electrical connection: contact pin's Example for order code: SPTSM 6 0512 BZ 5 TTL A For higher quantities or on-going demand, additional options are available as described below on request For example: ■ Other pulses per revolution: 1250 / 2000 / 2048 / 2500 / 4000 / 4096 / 5000 ■ Applicable on other shaft...

Open the catalog to page 3

Series SPTSM Data Sheet for Angle SensorsOptical Kit Encoder Assembling Instructions: General installation instructions: 1. When unpacking the components and during assembly, make sure that the optical disc is not touched in the area of the increments. The encoder disc and the optical module shall not come into contact with oil and / or grease. Wearing latex or cloth gloves during installation is helpful. 2. Take care to apply the ESD protection guidelines when handling the optical module. We recommend leaving the ex works shipped ESD protection on the electrical contacts of the optical...

Open the catalog to page 4

Series SPTSM Data Sheet for Angle SensorsOptical Kit EncoderAssembling Instructions: Step C C 1. Put a gentle pressure on the encoder disk from above (1) meanwhile you fasten the grub screw with a grub screw (hexagon) screwdriver wrench width 0.9 (2) Take care that the torque which is applied to the grub screw is not higher then 5.5 Ncm Secure the grub screw by means of a screw safety varnish (anaerobe liquid adhesive) D1. Place the optical module as shown in the image, with the pins upwards on the base plate (1) Note: Avoid touching the contact pin's of the optical module during assembly....

Open the catalog to page 5

Data Sheet for Angle Sensors Series SPTSM with Plug Housing Matching fastening Screw Mating Connector: MOLEX: KK 254 Crimp Ho KK 254 Crimp Terminal Se Matching fastening Screw ISO 7380-1 M3 Tightening torque max. 0,6 Nm Mating Connector: 16,9 ±0,5 MOLEX: KK 254 Crimp Housing, 5 Circuits, Series 2695 KK 254 Crimp Terminal Series 2759 Material Limitation according to 2011 Standard: applicable on shaft Performance data see Megatron data sheet M The copying, use, distribution or disdosure of the confident strictly prohibited without prior written consent. Any breach rights in the event of the...

Open the catalog to page 6

with Plug Housing 1 Data Sheet for Angle Sensors Series SPTSM Optical Kit ghtening torque max. 5,5NcmEncoder D d with Plug Housing Matching fastening Screw ISO 7380-1 M3 Tighteni Mating Connector: w/o Plug Housing MOLEX: KK 254 Crimp Housing, 5 Circuits, Series 2 Picture 1 KK 254 Crimp Terminal Series 2759 Mating Connector with Plug Housing MOLEX: SL Housing, 5 Circuits Series 70066 E SL Crimp terminal Series 70058 Performance data see Megatron data sheet B Mounting Tool: Centering Gauge The copying, use, distribution or disdosure of the confidentional and proprietary information contained...

Open the catalog to page 7

Series SPTSM Data Sheet for Angle Sensors Optical Kit Encoder Function Option B (2 Channels) Option BZ (3 Channels) PIN 2 Do not connect ! Channel Z (Index) Recommendations for mating connectors: Standard, contact pins (TTL output): MOLEX: KK 254 crimp housing, 5 circuits, series 2695 KK254 crimp terminals series 2759 For Option ST (with plug and TTL output): MOLEX: SL crimp housing, 5 circuits, series 70066 SL crimp terminals series 70058 For Option N (with plug and linedriver output): MOLEX: SL housing, 8 circuits, series 70066 SL crimp terminals series 70058 Recommended Output Circuit...

Open the catalog to page 8

SPTSM 9Pages

Catalog excerpts

All MEGATRON Elektronik GmbH & Co. KG catalogs and technical brochures

SPTSM
9Pages