Optical incremental Kit Encoder Series SPEH ■ Optical resolution until 1000 pulses per revolution ■ 22 mm housing diameter ■ 11.3 mm housing depth ■ Applicable for shaft diameters from 2 mm to 6.35 mm ■ 2 channels A+B ■ Supply voltage 5 VDC ■ Output TTL or linedriver ■ Integrated MOLEX coupling Very compact kit optical encoder. Thanks to the available mounting tools secure to install. For long shafts a borehole in the rear cover is available. With the integrated MOLEX plug-in connection, the encoder could be easy connected to the evaluation unit. This improves the handling during installation and service. Mechanical and Environmental Data, Miscellaneous Mechanical angle of rotation /stroke 1.) 360° without stop Max. allowed operational speed < 60.000 rpm (in dependence of the amount of pulses per revolution) Formula for calculation: max. rpm = (100000[1/s] x 60[s]) / pulses per rev. Max. acceleration 250000 rad/sec2 Operating temperature range -20..+100 °C Storage temperature range -20..+100 °C MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ [email protected] Errors and specifications subject to change without not

Optical incremental Kit Encoder Series SPEH Mechanical and Environmental Data, Miscellaneous Vibration (IEC 68-2-6, Test Fc) Shock (IEC 68-2-27, Test Ea) Housing diameter / length Housing depth Shaft diameter Shaft type Permissible axial play Permissible eccentricity + radial play Minimum shaft length incl. axial play Maximum shaft length incl. axial play Connection type Connection position Mass Fastening parts included in delivery Material housing Material disc Immunity ESD, human body model (MIL-STD-883, Method 3015.8) 20 g / 20 bis 2000 Hz / sine-shaped 75 g / 6 ms / halfsine 22 mm 11.5 mm...

Series SPEH Data Sheet for Angle SensorsOptical incremental Kit Encoder Order Code Requirement: Shaft diameter 6 mm, resolution 100 pulses per revolution , supply voltage 5 V, 2 channels A+B, output electronics TTL, back cover without borehole for longer shafts Example for order code: SPEH 6 100 5 B TTL A MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ [email protected] Errors and specifications subject to change without notice

Data Sheet for Angle SensorsOptical incremental Kit Encoder Series SPEH For higher quantities or on-going demand, additional options are available as described below For example: ■ Other hub diameters for other shaft diameters ■ Special connector and cable design Line Driver Differential Version Option: Cover Hole for Extended Shafts TTL Version Mating connector Housing: Molex # 51021-0400 Pins: Molex # 50079-8100 Accessory - not included in delivery: Mating connector with 500 mm AWG28 leads Line Driver Differential Version Mating connector Housing: Molex # 51021-0600 Pins: Molex # 50079-8100...

Data Sheet for Angle SensorsOptical incremental Kit Encoder Series SPEHInstallation instruction Assembly instruction The ESD guidelines must be followed during transport, storage, assembly and operation. Avoid touching the optical sensor and the optical disc in the area of the increments. Step 1: Place the base over the shaft and onto the mounting surface. Slide the centering tool onto the shaft so that it contacts and aligns the base. While applying light pressure to the centering tool, secure the base to the mounting surface using two screws. Step 2: Remove the centering tool and place the...

Optical incremental Kit Encoder Series SPEH Step 5: Remove the spacer tool and snap the cover down onto the base, (1). With your thumb and finger, squeeze the base latches together to ensure they are fully engaged with the cover, (2). MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ [email protected] Errors and specifications subject to change without notice