Data Sheet for Angle SensorsHall-Effect Single-Turn Rotary Encoder with Analog Output ■ Only 12.7 mm housing diameter ■ Suitable for shaft diameters from 2 mm..6.35 mm ■ Mounting ring and push on magnet are part of delivery ■ Supply voltage 5 VDC ■ Output signal analog absolute or PWM ■ Integrated MOLEX connector Extreme compact Hall Kit Encoder delivered as complete ready to setup package. The Package consisting of the encoder a mounting ring and the matching magnet holder and magnet for the shaft. With the MOLEX plug-in connection, the encoder could be easy connected to the evaluation unit. This improves the handling during installation and service. Effective electrical angle of rotation 1.) Independent linearity (best straight line) 1.) Output signal Resolution Update rate Supply voltage Power consumption (no load) Output load Mechanical and environmental data, Miscellaneous Mechanical angle of rotation 1.) Lifetime 2.) Max. operational speed Operating temperature range Storage temperature range Vibration (IEC 68-2-6, Test Fc) Housing diameter Housing depth Shaft diameter Shaft type 360° without stop Mechanically unlimited 10.000 rev./min. -40..+125 °C -40..+125 °C (5 Hz to 2 kHz) 20 g 12.7 mm 13.9 mm 2..6.35 mm Push on magnet for solid shafts MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ [email protected] Errors and specifications subject to change without noti

Hall-Effect Single-Turn Rotary Encoder with Analog Output Series MAB12AH Mechanical and Environmental Data, Miscellaneous Connection type Connection position Sensor mounting Mass Fastening parts included in delivery Fastening torque of the mounting screws for mounting ring Material mounting ring Material housing Material magnet holder Molex plug on sensor: 53398-0371 Axial Mounting ring Magnet + magnet holder + kit encoder + mounting ring: app. 20 g Kit Encoder, mounting ring, push on magnet Not included in delivery: 2 pcs. lens head screws 4-40 1/4" for mounting of the mounting ring 0.67 Nm...

Hall-Effect Single-Turn Rotary Encoder with Analog Output Series MAB12AH Order Code Order example MAB12AH: Requirement: Shaft diameter 6.00 mm, VSUP=5 V, output signal OUT=0..5 V (ratiometric), sense of rotation CW, effective electrical angle 360°, electrical connection: integrated connector in sensor housing Example for order code: MAB12AH 6 0505 CW360 K Additional options For higher quantities or on-going demand, additional options are available as described below on request For example: ■ Special cable and connection design ■ Sense of rotation CCW ■ User defined electrical angle MEGATRON Elektronik...

Data Sheet for Angle Sensors Hall-Effect Single-Turn Rotary Encoder with Analog Output Series MAB12AH Technical Drawing Terminal lay-out and connector Pin 1 +5VDC Connector in the sensor: Counter connector housing: Crimp pins for counter conn.: Crimp tools: Molex # 53398-0371 Molex # 51021-0300 Molex # 50079-8100 Molex # 50079 Please take care ! That the max. allowed axial mounting tolerances from the leading edge of the shaft to the mounting surface are 5.6 +0.8/-0.4 mm Leaving the tolerance band lead to signal loss and malfunction of the encoder. Mounting sketch Shaft center Radial mounting...

Data Sheet for Angle Sensors Hall-Effect Single-Turn Rotary Encoder with Analog Output Mounting Instruction During transport, storage, assembly and operation, it must be followed the ESD guidelines. MAE3 Assembly Instructions MAE3 Assembly Instructions Step 1: Slip push-on magnetic hub over shaft and firmly press down until top of shaft fills cavity of hub. Slip push-on magnetic hub over shaft and firmly press down until top of shaft fills cavity of hub. Step 2: Place encoder body over shaft assembly so that it sits on mounting surface. Step 2: Place encoder body over shaft assembly so that Step...