Hall-Effect Linear Sensor Series LHK ■ Long lifespan - 100 million movements ■ No wear-induced degradation of signal quality ■ Reliable measurement even at vibration ■ Resolution: 12 bit ■ Analog output: 0,5..4,5 V enables wire break detection and short-circuit detection ■ Supply voltage: 5 V The Hall-Effect Linear Sensor LHK is optimal for the detection of small, dynamic movements in automatically regulated systems without loss of accuracy due to wear. Compared to other non-contacting measurement principles it offers an excellent price / performance ratio. The sensor provides an active output signal which eliminates a complicated signal conversion. 30 mm ± 0,5mm ± 0,5 % 0,5..4,5 V ratiometric 12 bit (4096 digits) typ. 0,4 ms max. 10 ms 5 V ±10% < 15 mA < 30 mA > 10 kOhm 500 VAC, 1min 1000 MOhm @ 500 VDC max. ± 0,8 % V t x FS out Effective electrical stroke 1.) Independent linearity (best straight line) 1. Output signal Theoretical resolution 1.) Update rate Switch-on delay Supply voltage Power consumption (no load) Single output Redundant output Output load Insulation voltage 1.) Insulation resistance 1.) Temperature behaviour of signal Mechanical stroke 1.) Lifespan (90% Effective electrical stroke) 2.) Without spring return With spring return Bearing Max. operational speed Operational torque @ ambient temperature 1.) 2.) Without spring return With spring return Operating temperature range Storage temperature range Protection grade (IEC 60529) Protection grade push rod (IEC 60529) standard Vibration (IEC 68-2-6, Test Fc) Shock (IEC 68-2-27, Test Ea) Connection type Mass approx. 34 mm > 100 Mio. rod movements approx. 20 Mio. rod movements Sleeve bearing 1,76 m/s < 0,6 N ca. 2,5 N -40..+105°C (increased temperature range on request) -40..+105°C IP65 No sealing (IP40 equivalent) 20 g (10..2000 Hz, 12 h) 100 g (6 ms, 18x) Single strands AWG24 150 ±20 mm approx. 44 g MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Date: 12/12/2019 Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ [email protected] Page: 1 of 4 Specifications are subject to change without noti

Hall-Effect Linear Sensor Series LHK Mechanical and Environmental Data Fastening parts not included in delivery 2 x M3 Material shaft Stainless steel Material housing Plastic 1.) According IEC 60393 2.) Determined by climatic conditions according to IEC 68-1, para. 5.3.1 without load collectives 100 V/m (80 Mhz ~ 1 GHz, 1kHz with 80% Amplitude modulation) ± 8 kV contact discharge ± 15 kV aerial discharge Order code For higher quantities or on-going demand, additional options are available as described below Customized programming of the output signal For example: ■ Other minimum and maximum signal...

Data Sheet for Linear Sensors Series LHK Hall-Effect Linear Sensor Drawing Without spring return: 3 pcs. in case of single output 4 pcs. in the case of dual output (on request) 6 pcs. in the case of redundant output With spring return: 5V OUT A OUT B (In case of a parallel output) Single output WHT：OUTA BLK：G-A （GND） RED：IN-A （5V） On request dual output Output Voltage WHT：OUTA BLU：OUTB OUT B (In case of a crossing output) Redundant output BLK：G-A （GND） GRN：IN-B （5V） BLU：OUTB YLW：G-B （GND） Mechanical Stroke Approx. 34mm MEGATRON Elektronik GmbH & Co. KG ▪ Hermann-Oberth-Strasse 7 ▪ 85640 Putzbrunn...

Data Sheet for Linear Sensors Series LHK Hall-Effect Linear Sensor Installation suggestion Without spring return: Bore hole in the attachment is bigger than rod diameter. Small movements in the direction of the arrow are possible. Attachment of the application Set collar (e.g. DIN 705) Push on fastener (e.g. Quicklock ®) With spring return: workpiece MEGATRON Elektronik GmbH & Co. KG ▪ Hermann-Oberth-Strasse 7 ▪ 85640 Putzbrunn / Munich Tel.: +49 89 46094-0 ▪ Fax: +49 89 46094-201 ▪ www.megatron.de ▪ [email protected] Specifications are subject to change without notice Date: Page: