ETP25
6Pages

Catalog excerpts

Data Sheet for Angle SensorsHall-Effect Single-Turn Rotary Encoder with PWM Output ■ PWM output ■ Connecting possibilities: solder lugs or clamping terminal ■ Versatile factory programming possibilities The Series ETP25 can easy installed in the application based on the central thread. The high reliable Hall-Effect technology provides a constant signal quality over the whole life cycle. Effective electrical angle of rotation 1.) Independent linearity (best straight line) 1.) Absolute Linearity 1.) Output signal Output signal voltage Carrier frequency Minimum duty cycle Maximum duty cycle Resolution Supply voltage Power consumption (no load) Output load Insulation voltage 1.) Insulation resistance 1.) 10° < a < 360° (programmable in factory), ±0.5° ±0.4 % @ 360° ±0.6 % @ 360° PWM (pulse width modulation) 5V 244Hz (constant) 10%, equal to app. 0.4ms 90%, equal to app. 3.5ms 12Bit 5 V ±10 % < 10 mA > 5 kOhm 1000 VAC @ 50 Hz, 1 min 2 MOhm @ 500 VDC, 1 min Mechanical and Environmental Data Mechanical angle of rotation 1.) Endless Lifetime 2.) > 100 Mio. shaft rotating movements For Option D (with shaft sealing) the sealing is at least working up to 200 000 shaft rotating movements Bearing Sleeve bearing Max. operational speed 100 rpm (800 rpm within short time) Operational torque without / with X-Ring 0.1 < M < 0.6 Ncm / 0.3 < M < 1.3 Ncm (@ RT, 10 rev./min) Operating temperature range -40...+85 °C (fixed cable) Storage temperature range -40...+105 °C Protection grade front side (IEC 60529) Standard IP40 Option D (with shaft sealing) IP55M, IP66S Protection grade rear side (IEC 60529) Solder- and clamping terminals IP40 (solder pads and connectors excluded) Vibration (IEC 68-2-6, Test Fc) ±1.5 mm / 20 g / 10 bis 2000 Hz / 16 frequency cycles (3x4 h) Mechanical shock (IEC 68-27, Test Ea) 50 g / 11 ms / halfsine (3x6 shocks) MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Date: 03/26/2018 Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ info@megatron.de Page: 1 of 6 Errors and specifications subject to change without notic

Open the catalog to page 1

Data Sheet for Angle Sensors Series ETP25 Hall-Effect Single-Turn Rotary Encoder with PWM Output Max. radial load 1 Mass (product with option L) Fastening parts included in delivery Stainless steel Material housing Material shaft Hex nut (AF14) and tooth washer, if option D is ordered then an additional O-Ring is part of delivery as sealing between mounting panel and rotary encoder. Fastening torque mounting nut Plastic / Bronze EN 61000-4-6 Conducted sine wave EN 61000-4-8 Power frequency magnetic fields 1.) According IEC 60393 2.) Determined by climatic conditions according to IEC 68-1,...

Open the catalog to page 2

Data Sheet for Angle SensorsHall-Effect Single-Turn Rotary Encoder with PWM Output Series ETP25 Order Code Requirement: Shaft 0 6.00 mm, shaft length 22 mm, VSUP=5 V / OUT=244 Hz, sense of rotation CW, rotation angle 360°, no shaft sealing, electrical connection solder lugs, anti rotation pin A Example for order code: ETP25 6,35x22 5PWM CW 360 LA The rotary encoder ETP25 supplies as output signal 244Hz constant carrier frequency with defined high low ratio. The duty cycle (ratio between high and low value) changes in dependency of the rotation angle. The duty cycle lies between 10% and 90%....

Open the catalog to page 3

Data Sheet for Angle SensorsHall-Effect Single-Turn Rotary Encoder with PWM Output Series ETP25 Additional options: For higher quantities or on-going demand, additional options are available as described below on request For example: ■ Special shaft design ■ Special cable and connection design ■ Special torque MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ info@megatron.de Errors and specifications subject to change without notice

Open the catalog to page 4

Data Sheet for Angle Sensors Series ETP25 Hall-Effect Single-Turn Rotary Encoder with PWM Output Drawing Technische Zeichnung 1 View shows ETX25 without inner teeth washer and hex nut. Standard shaft dimensions Shaft length A 22 mm Tightening torque of h Shipment with inner te Material Limitation according to 2011/65/E The copying, use, distribution or disdosure of the confidentional a strictly prohibited without prior written consent. Any breach shall s rights in the event of the grant of a patent or the registration of au Signal sequence Mounting Surface MEGATRON Elektronik GmbH & Co.KG...

Open the catalog to page 5

Data Sheet for Angle Sensors 6 Hall-Effect Single-Turn Rotary Encoder with PWM Output A Drawing Technische Zeichnung Picture 2 Connector Phönix: MCV0,5-3-G2,5 FK-MC0,5-3-St2,5 Cable- and Pin-assignment ETP25 Function planarity of installation surface roughness of installation surface Tightening torque of hex nut ≤ 3Nm Shipment with inner teeth washer and hex nut (AF14) terial Limitation according to 2011/65/EU (RoHS) and Regulation (EC) No.1907/2006 (REACH) The copying, use, distribution or disdosure of the confidentional and proprietary information contained in this document(s) is strictly...

Open the catalog to page 6

ETP25 6Pages

Catalog excerpts

All MEGATRON Elektronik GmbH & Co. KG catalogs and technical brochures

ETP25
6Pages