Hall-Effect Singleturn Rotary Encoder with incremental output Series ETI25 ETI25 - R Up to 1024 pulses per revolution (4096 steps) factory programmable 1..128 ppr, 256 ppr, 512 ppr Versatile connecting possibilities: Solder- or clamping terminals, flat ribbon or round cable Electrical Interfaces Push-Pull, Open-Collector, TTL Compact 025 mm housing Simple to mount bushing design Electrical Data Output Signal Number of pulses Limit frequency Switch-on delay Supply voltage Power consumption (no load) Output load Max. Pull-Up Voltage Insulation voltage 1.) Insulation resistance 1.) TTL Push-Pull Open Collector Mechanical and Environmental Data Life time 2.) > 100 Mio. shaft rotating movements For Option D (with shaft sealing) the sealing is at least working up to 200 000 shaft rotating movements Bearing Sleeve bearing Operational torque without / with X-Ring 0,1 < M < 0,6 Ncm / 0,3 < M < 1,3 Ncm (@ RT, 10 rev./min) Operating Temperature range -40..+85 °C (fixed cable) Storage temperature range -40.. + 105 °C Protection grade front side (IEC 60529) Standard IP40 Option D (with shaft sealing) IP55M, IP66S Protection grade rear side (IEC 60529) Solder- and clamping terminals IP50 (solder pads and connectors excluded) Flat ribbon - and round cable IP66 (end of cable excluded) Vibration (IEC 68-2-6, Test Fc) ±1,5 mm / 20 g / 10 bis 2000 Hz / 16 frequency cycles (3x4 h) Mechanical shock (IEC 68-27, Test Ea) 50 g / 11 ms / half-sine (3x6 shocks) MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Date: 02/28/2020 Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ [email protected] Page: 1 of 7 Specifications are subject to change without notice

Data Sheet for Angle Sensors Hall-Effect Singleturn Rotary Encoder with incremental output Max. radial load 1 Mass (product with option 2 L) Fastening parts included in delivery Hex nut (AF14) and tooth washer, if option D is ordered then an additional O-Ring is part of delivery as sealing between mounting panel and rotary encoder. Fastening torque mounting nut Material shaft Stainless steel Material housing Plastic / Bronze EN 61000-4-3 RF sine wave EN 61000-4-6 Conducted sine wave EN 61000-4-8 Power frequency magnetic fields 1.) According IEC 60393 2.) Determined by climatic conditions according...

Data Sheet for Angle SensorsHall-Effect Singleturn Rotary Encoder with incremental outputOrder Code Description Selection: standard=black/bold, possible options=grey/cursive Shaft diameter, shaft length: Shaft diameter 0 6 mm, shaft length 22 mm Option: Shaft diameter 0 6.35 mm, shaft length 22 mm Option: User defined shaft [mm] 0 <6.35mm Number of pulses (pulses per revolution): Option: user defined pulses (<128) 0XXX Supply voltage / Output signal: VSUP=24 V (10...30 V) / OUT=A, B, Z, Push-Pull VSUP=24 V (10...30 V) / OUT=Open Collector VSUP=5 V ± 10% / OUT=A, B, Z, TTL VSUP=3,3 V ± 10% / OUT=A,...

Hall-Effect Singleturn Rotary Encoder with incremental output Series ETI25 Additional options For higher quantities or on-going demand, additional options are available as described below on request For example: ■ Output of absolute value by incrementing the signals after power on ■ Alteration of the signal sequence and index position ■ Special shaft design ■ Special operational torque ■ Special cable assembly, cable length MEGATRON Elektronik GmbH & Co. KG ■ Hermann-Oberth-Strasse 7 ■ 85640 Putzbrunn / Munich Tel.: +49 89 46094-0 ■ Fax: +49 89 46094-201 ■ www.megatron.de ■ [email protected] Specifications...

Data Sheet for Angle Sensors Hall-Effect Singleturn Rotary Encoder with incremental output 1 View shows ETX25 without inner Mounting Surface teeth washer and hex nut. View shows ETX25 without inner teeth washer and hex nut. Standard shaft dimensions Shaft length A 22 mm Pattern of Drilling Option TTL 05 View shows 0° position Hermann-Oberth-S MEGATRON Elektronik GmbH & Co.KG 85640 Putzbrunn / Mü Hermann-Oberth-Str. 7 Telefon: 089/46094-0 info@megatron 85640 Putzbrunn / München Telefon: 089/46094-0 [email protected] / www.m MEGATRON Elektronik GmbH & Co. KG ▪ Hermann-Oberth-Strasse 7 ▪ 85640 Putzbrunn...

Mounting Surface Mounting Surface Connector Phoenix: Connector Phönix: MCV0,5-5-G2,5 MCV0,5-5-G2,5 FK-MC0,5-5-St2,5 FK-MC0,5-5-St2,5 planarity of installation surface Option R Picture 1 Picture 2 (cable option F) (cable option R) ure 1 roughness of installation surface ble option R) Data Sheet for Angle Sensors Tightening torque of hex nut ≤ 3Nm Shipment with inner teeth washer and hex nut (AF14) Material Limitation according to 2011/65/EU (RoHS) and Regulation (EC) No.1907/2006 (REACH) Die Weitergabe sowie Vervielfältigung dieser vertraulichen Unterlage(n), Verwertung und Mitteilung ihres Inhaltes...

Data Sheet for Angle Sensors Hall-Effect Singleturn Rotary Encoder with incremental output Cable and pin assignment for option L, K Cable and pin assignment for option F Function: Push-Pull, TLL, Open Col Function: Push-Pull Cable and pin assignment for option R Option R Function: Push-Pull, TTL, Open Col MEGATRON Elektronik GmbH & Co. KG ▪ Hermann-Oberth-Strasse 7 ▪ 85640 Putzbrunn / Munich Tel.: +49 89 46094-0 ▪ Fax: +49 89 46094-201 ▪ www.megatron.de ▪ [email protected] Specifications are subject to change without notice Date: Page: