Data Sheet for Angle Sensors Series ETA25PM Hall Effect Multiturn Rotary Encoder with Analog Output 10 to 100-times longer life compared with multiturn potentiometers Free user programmable start and end position (electrical angle 10° up to 72000°) Simple user programming Space saving bushing mounting, housing with 25mm diameter The Series ETA25PM offers based on the programming interface an easy and exact adaptation to the application. This helps reducing costs and the number of different versions in stock. Electrical Data Effective electrical angle of rotation Independent linearity (best straight line) Absolute Linearity 0...10° - 0...72000° (max. 200 turns) Start point, endpoint and sense of rotation programmable by customer. Ex works the angle is set to 3600°. For detecting absolute position >360 the sensor should not be turned more than ±179° without supply voltage. ±0.05 % @ 3600° Output signal Update rate Supply voltage Power consumption (no load) Output load Insulation voltage Insulation resistance Max. number of programming cycles Mechanical and Environmental Data Mechanical angle of rotation Lifetime > 100 Mio. shaft rotating movements For Option D (with shaft sealing) the sealing is at least working up to 200 000 shaft rotating movements Bearing Max. operational speed Operational torque without / with X-Ring Sleeve bearing 100 rpm (< 1 min 800 rpm) 0,1 ≤ M ≤ 0,6 Ncm / 0,3 ≤ M ≤ 1,3 Ncm (@ RT, 10 rev./min) Operating temperature range: Flat band or round cable (option F or R) With integrated programming board (option TS) Storage temperature range: Flat band or round cable (Option F or R) With integrated programming board (option TS) Protection grade front side (IEC 60529) Standard Option D (with shaft sealing) Protection grade rear side (IEC 60529) Flat ribbon - and round cable (Option F or R) With integrated programming board (option TS) Vibration (IEC 68-2-6, Test Fc) 3.) Mechanical shock (IEC 68-27, Test Ea) 3.) IP66 (end of cable excluded) IP00 ±1,5 mm / 20 g / 10 to 2000 Hz / 16 frequency cycles (3x4 h) 50 g / 11 ms / halfsine (3x6 shocks) MEGATRON Elektronik GmbH & Co. KG ▪ Hermann-Oberth-Strasse 7 ▪ 85640 Putzbrunn / Munich Tel.: +49 89 46094-0 ▪ www.megatron.de ▪ [email protected] Specifications are subject to change without no

Data Sheet for Angle Sensors 2 Hall Effect Multiturn Rotary Encoder with Analog Output Mechanical and Environmental Data Max. radial load Fastening parts included in delivery 3 Fastening torque mounting nut 4 Material shaft Stainless steel Material housing Plastic / Bronze EN 61000-4-6 Conducted sine wave EN 61000-4-8 Power frequency magnetic fields 1.) According IEC 60393 2.) Determined by climatic conditions according to IEC 68-1, para. 5.3.1 without load collectives 3.) Not tested for Option TS Pin A Relationship between anti rotation pin and effective electrical angle in the state of delivery...

Data Sheet for Angle Sensors Series ETA25PM Hall Effect Multiturn Rotary Encoder with Analog Output Order Code Description: User programmable multiturn rotary encoder. Sense of rotation, rotation angle ex works: CW, 3600° Selection: standard=black/bold, possible options=grey/cursive Shaft diameter x shaft length: Ø6 x 22 mm Option Ø6,35 x 22 mm Option user defined shaft dimensions X x XX [mm] Ø ≤6,35mm Supply voltage / Output signal: VSUP=24 V (9...30 V) / OUT=0...5 V (not available for option TS) VSUP=24 V (15...30 V) / OUT=0...10 V Shaft sealing: Standard without shaft sealing Option D with...

Data Sheet for Angle Sensors Series ETA25PM Hall Effect Multiturn Rotary Encoder with Analog Output Additional options: Order example ETA25PM: Requirement: Shaft Ø 6.00 mm, shaft length 22 mm, VSUP=5 V / OUT=0...5 V, sense of rotation CW, rotation angle ex works 3600° (can be programmed by customer), no shaft sealing, flat ribbon cable 1.00 m, anti rotation pin B Example for order code: ETA25PM 6x22 0505 R1.00B For higher quantities or on-going demand, additional options are available as described below on request Examples: Special shaft design Special cable and connection design Special torque...

Data Sheet for Angle Sensors Hall Effect Multiturn Rotary Encoder with Analog3 Output 1 2 1 Mounting Surface 25 ±1 The following drawing is applicable for option R and F Mounting Surface Mounting Surface 1,5 ±0,2 Picture 2 (cable option F) Picture 1 (cable option R) Picture 1 (cable option R) Picture 2 (cable option F) 0,1 planarity of installation surface roughness of installation surface Picture 1 (cable option R) Tightening torque of hex nut ≤ 3Nm Shipment with inner teeth washer and hex nut (AF14) Material Limitation according to 2011/65/EU (RoHS) and Regulation (EC) No.1907/2006 (REACH)...

The RED LED light disappears and starts flashing GREEN at 4 Hz for 2s and changes to continuously light in GREEN for 5 -Release button when LED starts to light continuously after 5s the LED goes out (= confirmation of END position) In case of false sense of rotation (e.g. CW/CCW-switch set to CW, teach-in was done CCW) LED starts to flash alterna FYI: START position at teach-in is set to ZERO-degree location of effective electrical travel Setting ZERO-degree location (Reference modus): Data Sheet for Angle Sensors -Turn sensor to desired ZERO position and press START button LED starts flashing...