MPCT300 P6
37Pages

{{requestButtons}}

Catalog excerpts

MPCT300 P6 - 5

1.0 OVERVIEW The MPCT300 P6 model has 5 main programmable functions: RPM meter, frequency meter, hourly production meter, timer, and uni-directional pulse counter. Each one of these five functions is independent and they can’t be used at the same time. Main characteristics are: • count memory at the switching off (you can exclude this function from the menu). • six digits for counting. • NPN or PNP inputs (open collector or passive pull-up) or not amplified proximity (configured by jumpers or terminal connections) • up to three exchange relay alarm outputs (5A switch) (option ) •...

Open the catalog to page 5
MPCT300 P6 - 6

Power absorption Dimensions Piercing template 1.2 DISPLAY MESSAGES Table 2 r.01.00 -OFL-UFLEr4 ErP 1 ErP 2 ErP 7 Software version overflow underflow Division by zero (programming menu item wrong) error in programming parameter: dEnO = 0 error in programming parameter: n.riF = 0 error in programming parameter: the Preset item is not compatible with the alarms set point DESCRIPTION OF THE FRONT COMMANDS Led AL1: alarm 1 status indication Led AL2: alarm 2 status indication Led Sign: no managed Led In: total counting indication Key : access at the programming functions : it visualises the total...

Open the catalog to page 6
MPCT300 P6 - 7

: it sets up decimal point (it can be disabled by the menu). Used for set up. Start counting if timer. : Clear count (can be disabled by the menu) / fast exit in menu : it visualises alarm set point (it can be disabled by the menu) BASIC TERMINAL BOARD DESCRIPTION Terminals 4-5-6 Terminals 7-8-9 Terminals 13 and 15 Terminal 16 Terminal 17 Terminal 18 Terminal 20 Terminal 22 Terminal 23 Terminal 24 - exchange relay output (AL2: 4 = Com, 5 = NC, 6 = NO) - exchange relay output (AL1: 7 = Com, 8 = NC, 9 = NO) - instrument power supply (verify the instrument’s label to understand the power...

Open the catalog to page 7
MPCT300 P6 - 8

1.4 WIRING SCHEMATICS FOR COUNTER, REVOLUTION COUNTER PNPProx connection

Open the catalog to page 8
MPCT300 P6 - 9

Magnetic pick-up (IBT option) connection 7.5 WIRING SCHEMATICS FOR TIMER NPN or PNP prox connection (see paragraph "PRINTED CIRCUIT BOARD (PCB)

Open the catalog to page 9
MPCT300 P6 - 10

Switch connection key to get into the programming menu. key to search the item to program. If the set up needs a number to write, use the key to move the blinking digit and confirm with If the set up needs the selection of an item, use To exit the menu, press : the modified parameters will be stored.

Open the catalog to page 10
MPCT300 P6 - 11

1.7 RPM, FREQ. OR PR.H INSTRUMENT MENU FLOW fast alarms frequency meter installation remarks" hourly production alarms" The-► symbol means:

Open the catalog to page 11
MPCT300 P6 - 12

1.8 COUNTER INSTRUMENT MENU FLOW fast alarms timer alarms"

Open the catalog to page 12
MPCT300 P6 - 13

1.9 TIMER INSTRUMENT MENU FLOW fast alarms timer alarms" requested scale

Open the catalog to page 13
MPCT300 P6 - 14

1.10 PRINTED CIRCUIT BOARD (PCB) CONFIGURATION Open the instrument to configure the “Hold”, “Reset” and “Start” (NPN or PNP) inputs. To open the instrument use a screw-driver to lever on the long part of the keyboard and on the side hooks and extract the instrument from the front. The “Hold/Stop”, “Reset” and “Start” inputs are in NPN or MECHANICAL contact configuration (JP19 e JP20 in 3-2 position). To set up the “Reset”, “Hold/Stop” and “Start” inputs as PNP version, move the JP19 and JP20 jumpers in 1-2 position. 2.0 REVOLUTION COUNTER, FREQUENCY METER AND HOURLY PRODUCTION INSTALLATION...

Open the catalog to page 14
MPCT300 P6 - 15

MPCT300 P6 mect s.r.l. Table 3 Remarks n°seq. Press Appears on ° Key the display PASS Touch the “prog.” key to get into the 1 Prog. ↵ programming menu 0 000 In this phase the instrument asks for the 2 Prog. ↵ “password” number to protect the data programmation. (see “Password function”) Ou 3 InP 4 5 CPAS 5 5 AbtA 6 5 dEF 7 5 tYPE TYPE INSTRUMENT 8 5 rPn rPn = rpm meter 9 prog. ↵ Pr.h = hourly production meter FrEq = frequency meter CSEC = timer CIn = counter Select by “5“key “rPn” to program revolution counter, or “FrEq” to program frequency meter or “Pr.h” to program hourly production....

Open the catalog to page 15
MPCT300 P6 - 16

Appears on Remarks the display PASS Touch the “prog.” key to get into the programming menu 0 000 In this phase the instrument asks for the “password” number to protect the data programmation (see “Password function”) Ou InP FIL DIGITAL FILTER PROGRAMMING (look paragraph) n.rIF NOTCHES NUMBER 00001 set number of notches requested (1÷9999) **(press “prog. ↵” to confirm) n.rIF nUn MULTIPLAYING FACTOR 0.0000 Set multiplying factor value (1÷65535). This number will be the numerator of the correction constant (see “nUn and dEno function”) ** (press “prog. ↵” to confirm) nUn dEno DIVISION FACTOR...

Open the catalog to page 16
MPCT300 P6 - 17

mect s.r.l. Appears on the display Remarks PLO is req. ** (confirm to “prog. ↵”) Reset To exit from programming menu Exit ** see para. “SET-UPS” to change the set value. 2.2 "nUn" and “dEno” FUNCTION There are two menu items that allow to modify the displayed value by a constant factor. The “nUn” item allows to program a multiply factor in the range 1 ÷ 65535, and the “dEno” item allows to program a divide factor in the range 1 ÷ 65535. The constant factor will be: Where: X = “rPn measured” if the instrument is set up in revolution counter X = “Pr.h measured” if the instrument is set up in...

Open the catalog to page 17
MPCT300 P6 - 18

MPCT300 P6 mect s.r.l. To get the requested visualisation, you have to multiply the reading revolution/minute (RPM) by 0.55. To visualize the revolution/minute reading you must set up in the menu item “n.riF” = 4 (notches for revolution). To correct the visualisation by a 0.55 factor, you have to set up “nUn” = 55 and “dEno” = 100. Infact we know this relation: nUn 55 reading = RPM * _______ = RPM * _____ = RPM * 0.55 dEno 100 The unit can be programmed whit: selection “rPn” n. rIF = 4 nUn = 55 dEno = 100 • Make following setting on “hourly production” instrument. The parameter to be...

Open the catalog to page 18

All MECT SRL catalogs and technical brochures

  1. TPAC1008

    22 Pages

  2. TPAC1007

    14 Pages

  3. TPAC1006

    22 Pages

  4. MPA-MPV M6

    42 Pages

  5. MPA386 M6

    39 Pages

  6. MPP P6

    19 Pages

  7. MPA-MPV P6

    18 Pages

  8. MPX28

    8 Pages

  9. MPSN20

    2 Pages

  10. MPCV015

    20 Pages

  11. MPT390 M6

    61 Pages

  12. MPT91 M1

    66 Pages

  13. MPT90 M1

    46 Pages

  14. MPT60 M1

    45 Pages

  15. MPT100 M1

    35 Pages

  16. MPCIB396 P6

    41 Pages

  17. MPCIB20 M1

    25 Pages

  18. MPCT301 P6

    53 Pages

  19. MPCT30 P6

    36 Pages

  20. MPCT20 M1

    35 Pages

  21. MP2200 M6

    44 Pages

  22. MP1200 P6

    36 Pages

  23. MPPV340 M6

    40 Pages

  24. MPO347 M6

    40 Pages

  25. MPP323 M6

    42 Pages

  26. MPPV010 P6

    40 Pages

  27. MP45 P6

    18 Pages

  28. MPM P6

    34 Pages

  29. MP30 P2

    15 Pages

  30. MP20 M1

    35 Pages

  31. MPNC030

    12 Pages

  32. TPLC005

    28 Pages

  33. MPNC020

    13 Pages

  34. MPNC010

    25 Pages

  35. TP1070

    15 Pages

  36. TP1057

    15 Pages