- Catalogs
- Meagacon AS
- MSA11E Series
MSA11E Series
MSA11E Series
The MSA11E is a DC to DC signal isolator designed for applications requiring fully isolated DC signals relative to a DC input. It offers a wide range of factory-set input and output options and provides 1000V galvanic isolation with an ultra-fast response time of less than 50 milliseconds.
Compliance and Standards
The unit complies with IEC60092-504 and relevant environmental and EMC tests specified in IEC60068/60092 and IEC61000/60533, meeting the requirements of major Classification Societies.
Typical Applications
MSA11E is typically used to convert volt signals (0-10V) to mA signals (4-20mA) for PLC-based systems. Other ranges are available upon request.
Specifications
- AC Auxiliary Supply: 100-120, 200-240, 380-415, or 440-460VAC, 40-70Hz (Fuse 0.5A)
- Optional DC Auxiliary Supply: 12, 24, 48, or 110VDC (Fuse 2A)
- Contact Rating: AC: 100VA - 250V/2A max; DC: 50W - 100V/1A max
- Input Signals: Factory set mA ranges (e.g., 0-1, 0-5, 0-10, 4-20mA) and mV ranges (e.g., 0-60, 0-100, 0-500mV)
- Analogue Output: Ranges include 0-10, 0-20, 4-20mA (max 500ohm) and 0-5, 0-10V (min 100kohm)
- Temperature Range: -20 to +70ºC
- Weight: 0.7kgs
- Front Protection: IP52 (IP65 optional)
Dimensions
The unit is designed for DIN rail mounting with dimensions of 70mm x 100mm x 85mm.
Contact Information
For further information or to request other ranges, contact Megacon through their website at www.megacon.com.
Catalog excerpts
MSA11E • DC to DC signal isolator • A wide range of inputs and outputs (factory set) • 1000V galvanic isolation • Ultra fast - Less then 50mS response time Specifications AC Aux. Supply: Optional DC Aux.Supply: Contact Rating: Input signals: (Only factory set) (Other ranges on request) Analogue output: (Other ranges on request) Temperature: Weight: Front protection: MSA11E is used for applications where a fully isolated DC signal is required relative to a DC input. Typical applications involve converting volt signals (0-10V) to mA signals (4-20mA) for use with PLC based systems. Take contact for other ranges then listed under specifications. The unit meets IEC60092-504 and the relevant environmental and EMC tests specified in IEC60068/60092 and IEC61000/60533 respectively, to comply with the requirements of the major Classification Societies. Norway Denmark United Kingdom www.megacon.com ELECTRONIC CONTROL AND INSTRUMENTATION REF: Datasheet.MSA11E - REV: 1.01/03.2014 © All rights reserved to Megacon Megacon reserves the right to make any changes to the information at a
Open the catalog to page 1All Meagacon AS catalogs and technical brochures
MT-VA2 Pages
MT-VF2 Pages
MT-AW-R3 Pages
MT-FP2 Pages
MT-FW/R3 Pages
MXG105 LOAD UNIT1 Page
MEVx Series1 Page
MCVBx Series1 Page
MEVx-0,2 Series1 Page
MCVBx-0,2 Series1 Page
MSA11B Series1 Page
MSA12B Series1 Page
KPM30x Series2 Pages
KPM303x Series2 Pages
KCT3x Series1 Page
FA Frequency Meter Series5 Pages
Integra Series4 Pages
PQ Voltmeter Series6 Pages
SADPminiEx Series3 Pages
SADPmini Series4 Pages
Switches F1Pxx Series2 Pages
D.C. DIN Shunts2 Pages
KCM165K3 Pages
KPM465x3 Pages
KPM26x4 Pages
KPM163FQ2 Pages
KPM161FQ2 Pages
K R M 1 6 1 - D C1 Page
KPM 16xM3 Pages
K P M 1 6 x5 Pages
DC SIGNAL ISOLATOR1 Page
Voltage Comparator1 Page
SECTOR SYNCHRONISING RELAY2 Pages
GENERATOR CONTROLLER2 Pages
- Measuring device
- Panel panel meter
- Protection relay
- Power meter
- Illuminated indicator
- LED indicator
- Monitoring relay
- Current protection relay
- Digital protection relay
- DIN rail protection relay
- Voltage protection relay
- Electric motor protection relay
- Three-phase protection relay
- DIN rail monitoring relay
- Panel-mount protection relay
- Voltage measuring module
- Current measuring module
- Overload relay
- Voltage monitoring relay
- Phase protection relay