*mydirectindustry

KD115u

Product catalog summary

Description: The KD115u force sensor is designed for measuring contact force between electrodes in a spot welder, with adjustable electrode distance from 5mm to 20mm. It includes adapters with a 22mm diameter pressure surface and a 10mm contact surface distance. It can also measure radial force of seals or cutting force of tools.

Technical Data: The sensor is a compression type with a 22mm dimension and is made from anodised aluminium alloy. It has an input resistance of 390 Ohm and an output resistance of 350 Ohm. The excitation voltage ranges from 1 to 10 V, with a rated output of 1 mV/V. The accuracy class is 0.1%, with a relative linearity error and zero signal hysteresis of 0.05 %FS.

Connection Data: The sensor uses a round plug connector M12, 4-pole, male. The pin configuration includes positive and negative bridge supply and output, with specific wire colors assigned to each pin.

Accessories: Calibration certificates are available for up to 20 kN in compliance with DIN EN ISO/IEC 17025 and ISO 9000 standards. Various measuring amplifiers are available, including GSV-1H, GSV-2TSD-DI, and GSV-3USB, each with different housing, output, and sensitivity specifications.

Catalog excerpts

ME-Meßsysteme GmbH Neuendorfstr. 18a DE-16761 Hennigsdorf Mail [email protected] Web www.me-systeme.de Description The force sensor KD115u is particularly suitable for measuring the contact force between two electrodes of a spot welder. The distance between the electrodes can be adjusted in a range from 5mm to 20mm. Two Adapters with a circular pressure surface diameter 22mm are included. The distance between the contact surfaces is 10mm. The force insertion can be adapted for measuring radial force of seals or for measuring the cutting force of a tool.

Open the catalog to page 1

ME-Meßsysteme GmbH Neuendorfstr. 18a DE-16761 Hennigsdorf Mail [email protected] Web www.me-systeme.de

Open the catalog to page 2

ME-MeUsysteme GmbH Neuendorfstr. 18a DE-16761 Hennigsdorf Mail [email protected] Web www.me-systeme.de Technical Data Force sensor Type_ Force direction Force introduction Dimension 1 Sensor Fastening Dimension 2 Material Surface Height Length or Diameter Electrical Data Tolerance input resistance 40 Ohm Tolerance output resistance 3 Ohm Rated range of excitation voltage f 2.5 ... 5 V Operating range of excitation voltage f 1 ... 10 V Relative linearity error 0.05 %FS Relative zero signal hysteresis 0.05 %FS Temperature effect on zero signal 0.01 %FS/K Temperature...

Open the catalog to page 3

ME-MeUsysteme GmbH Neuendorfstr. 18a DE-16761 Hennigsdorf Mail [email protected] Web www.me-systeme.de Description positive bridge supply negative bridge supply positive bridge output negative bridge output Wire colour PIN Pressure load: positive output signal. Shield- transparent.

Open the catalog to page 4

ME-Meßsysteme GmbH Neuendorfstr. 18a DE-16761 Hennigsdorf Mail [email protected] Web www.me-systeme.de accessories Description Factory calibration certificate for force to 20 kN in accordance with DIN EN ISO / IEC 17025 and ISO 9000 for test materials monitoring according to DIN ISO 9001: 2008 with 5 load levels and 3 series of measurements. Compressive Force Measuring amplifier in desktop-housing for sensors with straingages. Serial port RS232, USB port, analogue output -5V...+5V, limiting frequency 260Hz, input sensitivity 3.5mV/V. Measuring amplifier in top-hat rail housing for sensors with...

Open the catalog to page 5

All ME-Messsysteme GmbH catalogs and technical brochures

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list