Safety Mats SM
20Pages

Polymer Electric Product information Safety Mats SM GmbH & Co. KG Polymer Electric Örlinger Straße 1–3 89073 Ulm Germany Tel.: +49 731 2061-0 Fax: +49 731 2061-222 E-mail: info.ulm@mayser.de Internet: www.mayser.com

Definitions See Definitions and Operation Principles in chapter 1 of the catalogue. Intended use A safety mat detects a person that is standing on or stepping onto it. It is a protective device covering a certain area and monitoring the presence of a person on it as a safety function. Its purpose is to prevent possible hazardous situations for personnel within a danger zone. Typical applications are in the area of moving units on machines and plants. The sensor is suitable for detection of walking aids. Safe operation of a safety mat depends entirely on - the surface condition of the...

10 Design Note: The standard version comes with a fully-bonded rubber surface topping GM1, GM4 or GM5 (see page 2.8). Standard version moulded on PVC plate Degree of protection: IP65 Customised versions Customised versions are available for special conditions, e.g. protection class IP68 or aggressive substances (fuels, solvents etc.). Available sizes Sensors are available up to a max. size of 1.5 m2. The side lengths must be within a range of 200 to 3,000 mm. L1: cable side L2: not cable side max. 1.5 m2 L1 L1 × L2 ≤ 1.5 m2 220312 v1.1 L2 The cable exit on safety mats can be on the wide or...

Non-sensitive zone along edges 40 The surrounding area of a sensor which does not have a sensing function: - 40 mm = on cable exit side - 10 mm = on remaining three sides 10 10 10 Note Where several sensors make up one contact area only the mat sides with 10 mm edges should lie next to one another. Connection Cable exit 220312 v1.1 The multifunctional cutout also allows the cable to be laid upwards or downwards. Subject to technical modifications. www.mayser-sicherheitstechnik.de Safety Mats SM 2.5

Wire colours Safety Mat SM/W black red Safety Mat SM/BK with 2 cables black black red red Safety Mat SM/BK with one cable blue white black brown Cable connection The cable connections are in the middle of the mat side. ATTENTION The maximum overall cable length up to signal processing is 200 m. Without plug (standard) - Universally applicable - Variable cable length with plug - Service-friendly - Easy assembly - Safe connection - atertight plug connection W possible 220312 v1.1 - Individual sensor SM/W or end sensor SM/W - Integrated resistor - 2-wire cable (Ø 5 mm; 2× 0.5 mm2 Cu) Subject...

- Feed-through sensor SM/BK - Without resistor - 2 two-wire cables (Ø 5 mm; 2× 0.5 mm2 Cu) - Feed-through sensor SM/BK - Without resistor - 4-wire cable(Ø 5 mm; 4× 0.25 mm2 Cu) Surface Toppings A rubber surface topping provides a non-slip surface and mechanical protection. The toppings are bonded flat to the sensors in the factory. GM1 or GM4 Sensor GM5 220312 v1.1 Sensor Subject to technical modifications. www.mayser-sicherheitstechnik.de Safety Mats SM 2.7

Rubber surface toppings Note Physical resistances: see table on page 2.8 and chemical resistance: see table on page 2.9 GM 1 SBR Round nap topping, black Round nap topping, yellow Thickness: 4.5 mm ±0.5 max. size: 1.0 m × 10 m 1.2 m × 10 m GM 4 NBR Round nap topping, black Round nap topping, yellow Thickness: 4.5 mm ±0.5 max. size: 1.0 m × 10 m 1.2 m × 10 m GM 5 NBR Round nap topping, green with high mechanical strength Thickness: 9 mm ±0.5 max. size: 1.2 m × 10 m Resistances The condition for the resistances listed in the following (at room temperature 23 °C) is a sensor with a rubber...

Chemical resistance The sensor is resistant against normal chemical influences such as diluted acids and alkalis as well as alcohol over an exposure period of 24 hrs. The values in the table are results of tests carried out in our laboratory to the best of our knowledge and belief. Liability cannot be derived from this information. The suitability of our products for your special area of application must always be verified with your own practical tests. Rubber surface topping Acetone Ammonia Brake fluid Cutting emulsion Acetic acid Greases Caustic potash solution Cooling lubricant Metal...

Polymer Electric Fixing sensors Ramp Edges can be installed quickly and easily. Z-profile (machine Side) Overview of fixing material Safety Mats SM 2.10 www.mayser-sicherheitstechnik.de

Polymer Electric Z-profile Sensor wilh ■ Nu', suitable lur plug-.n cable comect'O ■ Cable conduit tor max '¿ cables Z -rotilo Sensor with Suitable tor plug n cabla coincct.ons ■ Caolc conduit 'or man 10 cibi os Har p LdLjc AK 105 ' 0'ily 'c:' ier-iijr;, v. '.'i GM î lu'laCK ijpL" ;) Ramp Edge pouroo aler Ira-io assembly •■•.■>;■ ■ Suitable lor plug-m cable connections - Cable conduit for max. 10 cables

Aluminium Z- and aluminium Z/1-profile - Edging at the machine or wall side - Aluminium Z-profile for sensor GM 1 and GM 4: H = 17.0 mm - Aluminium Z/1-profile for sensor with GM 5: H = 21.0 mm - Aluminium Z-profile: Rod, 3 m (7500054), Rod, 6 m (1000011) or fixed length - Aluminium Z/1-profile: Rod, 3 m (7500738), Rod, 6 m (1001478) or fixed length 2 2 H 17 66 3.5 8 H Aluminium Ramp Edge AK 66 - 1-part with cable conduit - Combinations up to max. 2 sensors - Sensor without plug - Aluminium Ramp Edge for sensors with GM 1 and GM 4: H = 18.7 mm - Rod, 3 m (7500053), Rod, 6 m (1000008) or...

Aluminium Ramp Edge AK 105 and AK 105/1 - 2-part with cable conduit - For combination of several sensors - Sensors with or without plugs - Aluminium Ramp Edge AK 105 for sensors with GM 1 and GM 4: H = 17.5 mm - Aluminium Ramp Edge AK 105/1 for sensors with GM 5: H = 21.0 mm - Aluminium Ramp Edge AK 105: Rod, 3 m upper and lower sections (7500052), Rod, 6 m upper section (1000009), Rod, 6 m lower section (1000010), or fixed length - Aluminium Ramp Edge AK 105/1: Rod, 3 m upper section and lower section (7500224), Rod, 6 m upper section (1000992), Rod, 6 m lower section (1000010), or fixed...