Group: KEMAI MACHINERY & EQUIPMENT CO.,LTD
Catalog excerpts
Industry Technology Down The Hole Hammer & Bit
Open the catalog to page 1Down The Hole Hammer & Bit 01
Open the catalog to page 2The Characteristics Of High Air Pressure DTH Hammer -with foot valve It is a kind of valveless high air pressure DTH Hammer with foot valve It has the following characteristics: ♦ Valveless air distribution. More reliable. ♦ Simple design of the piston, long life. ♦ More efficient energy transfer,faster drilling speed, lower air consumption and lower oil consumption. ♦ Fewer internal parts, simple structure,longer life, Less failure and easier to maintain because all the parts are heat treated. ♦ Easy to disassemble because the top sub, the drive chuck and the external cylinder are...
Open the catalog to page 3MSD12 DTH HAMMER High Air Pressure with foot valve DTH Hammers Item Description According to your request,the top sub can be made into two spanners,and put protection buttons.An air controlling hole can be drilled on the check valve to provide more efficient cuttings discharge. Technical Date Length(Less bit) Detailed air consumption can be seen in appendix,P73
Open the catalog to page 4High Air Pressure with foot valve DTH Hammers Item Description According to your request,the top sub can be made into two spanners,and put protection buttons.An air controlling hole can be drilled on the check valve to provide more efficient cuttings discharge. Technical Date Length(Less bit) Detailed air consumption can be seen in appendix,P73
Open the catalog to page 5The Characteristics Of High Air Pressure -without foot valve DTH Hammers It is a kind of high air pressure DTH Hammer without foot valve,our newest design.It is also one of the most advanced DTH Hammers in the word. It has the following characteristics: Out of the trouble of foot valve fracture and expansion and contraction. Lower energy consumption and higher impact frequency. The drilling speed is 15%-30% higher than the same type with the valve Simple structure ,reliable parts, long life , easy and cheap maintenance. Lower air and oil consumption. The oil consumption is about...
Open the catalog to page 6High Air Pressure without foot valve DTH Hammers Item Description According to your request,the top sub can be made into two spanners,and put protection buttons.An air controlling hole can be drilled on the check valve to provide more efficient cuttings discharge. Technical Date Length(Less bit) Detailed air consumption can be seen in appendix,P73
Open the catalog to page 7MSD12A DTH HAMMER High Air Pressure without foot valve DTH Hammers Item Description According to your request,the top sub can be made into two spanners,and put protection buttons.An air controlling hole can be drilled on the check valve to provide more efficient cuttings discharge. Technical Date Length(Less bit) Detailed air consumption can be seen in appendix,P73
Open the catalog to page 8High Air Pressure without foot valve DTH Hammers Item Description According to your request,the top sub can be made into two spanners,and put protection buttons.An air controlling hole can be drilled on the check valve to provide more efficient cuttings discharge. Technical Date Length(Less bit) Detailed air consumption can be seen in appendix,P73
Open the catalog to page 9Bit Face Shape Selection Drop Center For high penetration rates in soft to medium hard and fissured rock formations. Low to medium air pressures. Maximum hole deviation control. Concave Face The all-round application bit face specifically for medium hard and homogenerous rock formations. Good hole deviation control and good flushing capacity. Convex Face For high penetration rates in soft to medium-hard with low to medium air pressures. It is the most resistance to steel wash,and may reduce the load and wear on the gauge buttons, but poor hole deviation control. Double Gauge Face This kind...
Open the catalog to page 10Carbide Button Shape Selection Domed/ Round Button Domed/ Round Buttons are usually used as gauge buttons of DTH Bits, suitable for very abrasive and very hard formations. Parabolic/Semi-Ballistic Button Parabolic buttons are usually used as gauge buttons and front buttons of DTH Bits, suitable for medium abrasive and hard formations. Ballistic Button Ballistic Buttons are usually used as front buttons of DTH Bits, suitable for medium abrasive and medium hard formations. They can also be used as gauge buttons if the rock is soft. Sharp Button Sharp Buttons are usually used as front buttons...
Open the catalog to page 1112" BIT Data Referenced By MSD12 Concave Face Bit Specification Of Products:SD12
Open the catalog to page 12Down The Hole Hammer & Bit 12
Open the catalog to page 13Drill Tube A OD (mm) Down The Hole Hammer & Bit 13
Open the catalog to page 14Down The Hole Hammer & Bit 14
Open the catalog to page 15Pin-Box Adapters Connection Down The Hole Hammer & Bit 15
Open the catalog to page 16Down The Hole Hammer & Bit 16
Open the catalog to page 17Breakout Bench Breakout Bench Operation Method ♦ Put hammer in the bench. . Adjust the position of hammer and wrench; use wrench to block the top sub side of hammer; let wrench and jack in the same face. ♦ Fix K-shaped base with nut. ♦ Fix wrench with nuts. ♦ Shake handle of Jack slowly till top sub away from hammer. ♦ After top sub dismantled, grease the jack, release nuts, discharge the K-shaped base and turn around the Hammer. ♦ Adjust the position of hammer and wrench ; use wrench to block the drive chuck of hammer;let wrench and jack in the same face. ♦ Fix K-shaped base and the wrench...
Open the catalog to page 18Comparison Line Chart Of Technical Date Down The Hole Hammer & Bit 18
Open the catalog to page 19"Globle Drilling Industry Experts No matter what kinds of rock-Soft rock,loose-medium rock, hard rock and any other special formations, just tell us what you need,our special Tailored service is waiting for you upon you demand. Industry Technology MAXDRILL ROCK TOOLS CO*,LTD Add: 9/F, Fuzhong International Plaza,No/72 Xinhua Road, Nan Ming District,Guiyang,Guizhou China Production Base: Er Guan Ba Industrial Area,Jiuchang Town,Xiuwen county,Guizhou Province,China Tel: 86-851-88639105/06/07 FAX: 86-851-88639108 Web: www.max-drilling.com Email: office@kemaico.com info@kemaico.com
Open the catalog to page 20All MAXDRILL ROCK TOOLS CO. catalogs and technical brochures
-
SELF-DRILLING ANCHOR SYSTEM
13 Pages
-
TAPHOLE DRILL BIT
4 Pages
-
TAPHOLE DRILL ROD
5 Pages
-
Y20 HAND-HELD ROCK DRILL
2 Pages
-
YT28 JACKLEG DRILL
2 Pages
-
BREAKER STEEL
1 Pages
-
12° TAPERED DRILLING TOOLS
6 Pages
-
DOWN THE HOLE BIT
4 Pages
-
6° TAPERED DRILLING TOOLS
6 Pages
-
7° TAPERED DRILLING TOOLS
5 Pages
-
DTH HAMMER
74 Pages
-
Drifting & tunneling
20 Pages
-
TopHammer-drilling-tools
63 Pages
-
integral drill steel
1 Pages
-
6° taper drill rod and bit
2 Pages
-
10 inch DTH hammer and bit
19 Pages
-
8 inch DTH hammer and bit
22 Pages
-
5 inch DTH hammer and bit
23 Pages
-
3 inch DTH hammer and bit
17 Pages
-
Down the hole drill bit--QL60
22 Pages
-
Rotary and cutting teeth
5 Pages
-
Wear parts
9 Pages
-
Engineering Cutter Tools
13 Pages
-
Concentric
6 Pages
-
Y24 Hand-Held Rock Drill
2 Pages
-
Maxdrill Break steel
1 Pages
-
Maxdrill Hand splitter
2 Pages
-
Maxdrill Plug Hole Rod
1 Pages
-
Maxdrill Rock Drills Y28
3 Pages
-
Maxdrill Rock Drills Y24
3 Pages
-
Maxdrill Rock Drills Y20
3 Pages
-
Maxdrill DTH drill pipes
4 Pages
-
Maxdrill Down The Hole Hammer
54 Pages
-
DTH Drill Pipes
4 Pages
-
Integral Drill Rod
5 Pages