Shin-G Series
293Pages

Catalog excerpts

A\ Safety Precautions • Important Notes on exporting this product or equipment containing this product; If the end-user or application of this product is related to military affairs or weapons, its export may be controlled by “Foreign Exchange and Foreign Trade Control Law” of Japan where export license will be required before product can be exported from Japan. • This product is designed and manufactured for use in General Purpose Industrial Equipment and it is not intended to be used in equipment or system that may cause personal injury or death. • All servicing such as installation, wiring, operation, maintenance and etc., should be performed by qualified personnel only. • Tighten mounting screws with an adequate torque by taking into consideration strength of the screws and the characteristics of material to which the product will be mounted. Over tightening can damage the screw and/or material; under tightening can result in loosening. ‘Example: apply 2.7 N-m - 3.3 N-m torque when tightening steel screw (M5) to steel surface. • Install safety equipment to prevent serious accidents or loss that is expected in case of failure of this product. • Consult us before using this product under such special conditions and environments as nuclear energy control, aerospace, transportation, medical equipment, various safety equipments or equipments which require a lesser air contamination. • We have been making the best effort to ensure the highest quality of our products, however, some applications with exceptionally large external noise disturbance and static electricity, orfailure in input power, wiring and components may result in unexpected action. It is highly recommended that you make a fail-safe design and secure the safety in the operative range. • If the motor shaft is not electrically grounded, it may cause an electrolytic corrosion to the bearing, depending on the condition of the machine and its mounting environment, and may result in the bearing noise. Checking and verification by customer is required. • Failure of this product depending on its content may generate smoke of about one cigarette. Take this into consideration when the application of the machine is clean room related. • Please be careful when using the product in an environment with high concentrations of sulfur or sulfuric gases, as sulfuration can lead to disconnection from the chip resistor or a poor contact connection. • Do not input a supply voltage which significantly exceeds the rated range to the power supply of this product. Failure to heed this caution may lead to damage of the internal parts, causing smoke and/or fire and other troubles. • The user is responsible for matching between machine and components in terms of configuration, dimensions, life expectancy, characteristics, when installing the machine or changing specification of the machine. The user is also responsible for complying with applicable laws and regulations. • Manufacturer’s warranty will be invalid if the product has been used outside its stated specifications. • Component parts are subject to minor change to improve performance. • Read and observe the instruction manual to ensure correct use of the product. Panasonic Corporation, Automotive & Industrial Systems Company, Electromechanical Control Business Division, Motor Business Unit 1-1 Morofuku 7-chome, Daito, Osaka574-0044, Japan Tel : +81-72-871-1212 Fax: +81-72-870-3151 The contents of this catalog apply to the products as of April 2016. • Printed colors may be slightly different from the actual products. • Specifications and design of the products are subject to change without notice for the product improvement. Compact AC Geared Motor

Open the catalog to page 1

^Information * Information contained in the catalog A- 2 • Product list A- 4 • Selection by keywords A- 24 • Product Type Contents Motor A- 28 Gear head A- 29 Speed controller A- 30 Brake unit A- 30 Special (produced to custom order) A- 31 Gear head A- 34 * Handling instructions A- 35 • Motor selection A- 46 • Safety standard approved motor A- 57 • Reversible motor B- 63 • Electromagnetic brake motor B-167 * Variable speed induction motor B-223 * Variable speed reversible motor B-267 * Variable speed electromagnetic brake single-phase motor...

Open the catalog to page 2

The catalog is divided into the following sections. • Information o a-2 to a-60 Information on product selection, terms used in this catalog, handling precautions and safety standards. * Product description <Motors> © B-1 to B-456 List of motors and gear heads Control related products * Options & index o d-1 to d-16 Options/mdex List of options. Index sorted by parts number. (Alphabetical order) • Handling instructions Description of special precautions and handling techniques that must be implemented to assure product performance. Q A-35 ^ Index • Each series is color...

Open the catalog to page 3

Product list Pinion shaft motor [Japanese version] Variable speed reversible Variable speed electromagnetic brake, single-phase Leadwire type Leadwire type Variable speed unit US series Leadwire type Sealed connector type Leadwire type Sealed connector type C&B variable speed induction Leadwire type

Open the catalog to page 5

* Pinion shaft * Round shaft <The models with a motor model number to which “A” or “B” is suffixed are not equipped with a capacitor cap.> * The models with a model number to which “A” or “B” is suffixed (not equipped with a capacitor cap) are not sold or available in Japan.

Open the catalog to page 7

Pinion shaft motor [International standard approved] <The models with a motor model number to which “A” is suffixed are not equipped with a capacitor cap.> * The models with a model number to which “A” is suffixed (not equipped with a capacitor cap) are not sold or available in Japan.

Open the catalog to page 8