Group: Matsushita Electric Works
Catalog excerpts
Narrow pitch RF connectors [For board-to-FPC] RF4 ( 0.35 mm pitch ) Height 0.65 mm Product Catalog
Open the catalog to page 1Narrow pitch RF connectors【For board-to-FPC】 RF4 ( 0.35 mm pitch ) Height 0.65 mm Compatible with 5G Millimeter-wave Antenna Modules. Excellent EMI/SI performance. FEATURES ● Seamless metal shield with all-around contact achieves both good EMI characteristics and high robustness ● Good SI characteristics with terminals for high frequency signals and shielded terminals 2.48 mm ● TOUGH CONTACT structure and shield lock structure achieves high contact reliability and high retention force TYPICAL APPLICATIONS ● Smartphone, Tablet, Laptop, Router etc. ・ For 5G Millimeter-wave Antenna/ UWB (...
Open the catalog to page 2■ Optimized high frequency signal terminals ■ Shielding between terminals achieves high SI performance Shielding terminals high frequency signals high frequency signals |~| : Shield [RF : RF signal S : General signal ORDERING INFORMATION ( PART NO. ) Product name 3B: RF4 Socket 4B: RF4 Header Mated height Function PRODUCT TYPES Mated height Notes) 1: Order unit: For volume production: 1-inner carton ( 1-reel ) units. For samples, please contact our sales representative. 2: Please contact our sales representative for connectors having a number of pins other than those listed above Panasonic...
Open the catalog to page 3Panasonic Industry Co., Ltd. Electromechanical Control Business Division industrial.panasonic.com/ac/e/ 3
Open the catalog to page 4Narrow pitch RF connectors RF4 ( 0.35 mm pitch ) Height 0.65 mm DIMENSIONS ( Unit: mm ) CAD The CAD data of the products with a mark can be downloaded from our Website. ■ Socket ( Mated height: 0.65 mm ) External dimensions ( Contact and Ground terminal ) * There might be differences in the exposure state of the ground terminal except terminal portion. ■ Header ( Mated height: 0.65 mm ) CAD ( Post and Ground terminal ) Panasonic Industry Co., Ltd. Electromechanical Control Business Division industrial.panasonic.com/ac/e/
Open the catalog to page 5■ Specifications for the plastic reel In accordance with EIAJ ET-7200B ■ Specifications for taping In accordance with JIS C 0806-3:1999. However, not applied to the mounting-hole pitch of some connectors. Tape I Type/Mated height Panasonic Industry Co., Ltd. Electromechanical Control Business Division industrial.panasonic.com/ac/e/ 5
Open the catalog to page 6Narrow pitch RF connectors RF4 ( 0.35 mm pitch ) Height 0.65 mm NOTES ( Unit: mm ) ■ Design of PC board patterns Conduct the recommended foot pattern design, in order to preserve the mechanical strength of terminal solder areas. ■ Recommended PC board and metal mask patterns Connectors are mounted with high pitch density, intervals of 0.35 mm, 0.4 mm or 0.5 mm. In order to reduce solder and flux rise, solder bridges and other issues make sure the proper levels of solder is used. The figures are recommended patterns. Please use them as a reference. ● Recommended PC board pattern ( TOP VIEW ) ●...
Open the catalog to page 7Notes on Using Narrow pitch RF Connectors/Narrow pitch Connectors/High Current Connectors About safety remarks Observe the following safety remarks to prevent accidents and injuries. • Do not use these connectors beyond the specification sheets. The usage outside of specified rated current, dielectric strength, and environmental conditions and so on may cause circuitry damage via abnormal heating, smoke, and fire. • In order to avoid accidents, your thorough specification review is appreciated. Please contact our sales representative if your usage is out of the specifications. Otherwise,...
Open the catalog to page 8• Select the placement machine taking into consideration the connector height, required positioning accuracy, and packaging conditions. • Be aware that if the chucking force of the placement machine is too great, it may deform the shape of the connector body or connector terminals. • Be aware that during mounting, external forces may be applied to the connector contact surfaces and terminals and cause deformations. • Depending on the size of the connector being used, self alignment may not be possible. In such cases, be sure to carefully position the terminal with the PC board pattern. •...
Open the catalog to page 9■ Hand soldering • Set the soldering iron so that the tip temperature is less than that given in the table below. Table A • Do not allow flux to spread onto the connector leads or PC board. This may lead to flux rising up to the connector inside. • Touch the soldering iron to the foot pattern. After the foot pattern and connector terminal are heated, apply the solder wire so it melts at the end of the connector terminals. Be aware that soldering while applying a load on the connector terminals may cause improper operation of the connector. Thoroughly clean the soldering iron. Flux from the...
Open the catalog to page 10■ Handling the PC board after mounting the connector When cutting or bending the PC board after mounting the connector, be careful that the soldered sections are subjected to excessive force. • To prevent problems from voids or air pockets due to heat of reflow soldering, avoid storing the connectors in areas of high humidity. • Depending on the connector type, the color of the connector may vary from connector to connector depending on when it is produced. Some connectors may change color slightly if subjected to ultraviolet rays during storage. This is normal and will not affect the...
Open the catalog to page 11Panasonic INDUSTRY Panasonic Industry Co.f Ltd. Electromechanical Control Business Division ■ 1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8506, Japan industrial.panasonic.com/ac/e/ Specifications are subject to change without notice. ASCTB124E 202309
Open the catalog to page 12All Matsushita Electric Works catalogs and technical brochures
-
High Current Connectors
12 Pages
-
Ultra-slim Photoelectric Sensor
16 Pages
-
Laser Distance Sensor
16 Pages
-
CA RELAYS
8 Pages
-
AQ-J RELAYS
19 Pages
-
AQ-H RELAYS
14 Pages
-
AQ-G RELAYS
14 Pages
-
AQ-A RELAYS (DC output type)
15 Pages
-
AQ-A RELAYS (AC output type)
17 Pages
-
AQ8 RELAYS
17 Pages
-
AQ1 RELAYS
16 Pages
-
HG-S series
18 Pages
-
HE
6 Pages
-
SFD-WL3
2 Pages
-
SF4D
42 Pages
-
ELC500
8 Pages
-
AC Fan Motor 80×38t
1 Pages
-
GT707
2 Pages
-
GT SERIES
24 Pages
-
GT32-R
2 Pages
-
Shin-G Series
293 Pages
-
MINAS-BL KV Series
52 Pages
-
LP-GS series
12 Pages
-
LP- V SERIES, LP- W SERIES
16 Pages
-
LP-M
12 Pages
-
ER-VW
8 Pages
-
ER-TF SERIES
6 Pages
-
ER-X001
4 Pages
-
EWA2
8 Pages
-
RJ RELAYS (ARJ)
5 Pages
-
SF Relays
4 Pages
-
mechDE Relays (ADE)
4 Pages
-
EX-L200
12 Pages
-
gtseries_e_cata
24 Pages
-
ce_up50_1
6 Pages
-
digest_e_cata
32 Pages
-
fx-100
20 Pages
-
uj30
12 Pages
-
Power relay selector chart
8 Pages
-
NEW & KEY PRODUCTS 2012
32 Pages
-
Aicure UJ30/35 Catalog
12 Pages
-
KW2G-H
4 Pages
-
LP-S series
12 Pages
-
LP-S500W
12 Pages
-
SC-GU3
8 Pages
-
SL-PK01
2 Pages
-
DPC-L100/DPH-L100
12 Pages
-
FP-X0
8 Pages
-
FPOR
20 Pages
-
PM 2
6 Pages
-
PM-24
6 Pages
-
LP-Z Series
4 Pages
-
LP-V/W Series
16 Pages
-
FP2SH
24 Pages
-
LP-300 Series
12 Pages
-
SF4B Ver.2
48 Pages
-
SL-VGU1-485
2 Pages
-
PM-44/PM-54
10 Pages
-
PV200
22 Pages
-
FX-500
20 Pages
-
Flat Type Fiber
2 Pages
-
LP-400 Series
16 Pages
-
MIPTEC catalog
8 Pages
-
PM-64
8 Pages
Archived catalogs
-
Lighting Control Catalog
42 Pages
-
Time Switches
2 Pages
-
Time & Synchronization VIC100
1 Pages
-
GPS Products Antennas
2 Pages
-
Phototriac Coupler
4 Pages
-
Signal Relays
31 Pages