Handy type Matsusada Prcision Compact / High speedPiezoDriver PZJ Series 1127-01A-1 ■ FEATURES 3ch piezo driving is possible. 镕 Peak current of 3 times more than rating current can be used. High-speed response. 1pF piezo device can be driven at sine wave of 1.3kHz (100Vp-p, at each 3ch). ՕDC bias can be set. Low ripple, high stability ՕClosed loop control is possible by using your displacement sensor. SUMMARY PZJ is a compact piezo driver. It is possible to drive piezo device with arbitrary waveform by amplification function of input waveform. 1-output type or 3-output type can be chosen depending on the number of axis required. Just one driver can support multiple driving like X-Y-Z. High power is realized for high-speed response in such a compact size. Peak power increase function that allows three times as much as rating enables high-speed displacement even in pulse driving, which will be required for such application as stage positioning. Also it is equipped with bias function thus enabling easy setting of reference point of displacement. As a basic model of piezo driver that is equipped with easy operability and high output, PZJ series are ideal for diverse piezo applications from research and development to integration to system. LINEUP Output voltage (Vdc) Rated output current lave * 1 (mAave) Peak output current Ip less than 10ms (mA) MODEL Frequency response Output resistor (W) Sine wave (-3dB) Rise time (approx. value with 1|iF load) single output type 3ch output type RL resistive load 1|jF load AV=100V 0 to Max V 0 to +100 300 900 PZJ-0.1P PZJ-0.1P x 3 DC to100kHz DC to 1.3kHz 0.1ms 0.1ms 10 0 to +150 200 600 PZJ-0.15P PZJ-0.15Px3 DC to 60kHz DC to 600Hz 0.2ms 0.3ms 20 0 to +300 100 300 PZJ-0.3P PZJ-0.3P x 3 DC to 30kHz DC to 150Hz 0.3ms 1ms 75 * 1 ; Output current when DC is 50% of rating current. *2 ; Calculated from peak output current value (can be output within 10ms) (Tr=C Vp-p/lp). Formula of Tr'=Tr- Ip/lave is used when calculated value of Tr exceeds the time for which peak current can be output (10ms). SPECIFICATIONS Input voltage' current Output voltage control DC bias 115VAC±10%, 50/60Hz single phase, 1.5Atyp. Protection Output over current protection by cutting-off when over current, over voltage, blackout prtection. Operation temperature 0°C to +40°C Storage temperature -20°C to +60°C External control voltage Vcon-in=0V to +10V Note 1 ) (Input impedance more than 10kW) Can be set from 0% to 100% (each ch is independent) by 10-turn potentiometer on front panel. ±0.05% (for 115V±10% input change) Note 2 ) Less than 0.01%p-p (with load of 50nF at maximum output voltage) Less than 0.02%/H Note2 ) Less than 0.02%/°C Note 2 ) Regulation Ripple Stability Temperature coefficient Humidity Accessories 20 to 80%RH(no condensation) 2.5m(8.2ft) input AC cable (1) 1.5m(5ft) output cable (terminal open) (3) Instruction manual (1) DC output 3.5 digit digital meter voltage display Displays average output voltage Note 1 ) Off set voltage in Vcon-in=0V is ±0.5% or within ±1V of rating output. Note 2) Value at max rating voltage with resistive load in DC operation.

PZJ Series OPTIONS 1127-01A-2 -L2 Output voltage monitor: 0V to +10V (output impdance 1kW, accuracy: ±1% F.S.) -LC Current limit: Output current is limited by dropping down the output voltage. -LS Remote switch ON/OFF: Output voltage can be turned ON/OFF by remote signal (each ch is done at the same time. Short=ON, Open=OFF). -LVs External sensor input terminal: Closed loop control can be done using signal of displacement sensor (0 to 10V). Distortion gauge as sensor Piezo actuator Piezo driver Distortion sensor (Distortion gauge) 0V to +10V Sensor amp. Input external sensor Vcon 0V to+10V Add...