Hydraulic Synchronized CNC Control
48Pages

MASTEEL BRAKE Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version 6.xx OPERATING MANUAL MASTEEL AMERICA CORPORATION #120 – 7490 MacDonald Road Delta, BC V4G 1N2 Canada Tel: (604) 952-4434 Fax: (604) 952-4432 E-mail: sales@masteels.com Web Site: www.masteels.com

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version OPERATING INSTRUCTION 1. POWER ON AND START UP 2. TP-700 CONTROL CONSOLE OPERATION 3. MAIN SCREEN DISPLAY 4. OPERATING CONTROLS 5. MUNUAL MODE:  SETTING UP BENDING POSITION and BENDING ANGLE  BACKGAUGE POSITION CONTROL 6. AUTO MODE: EDIT, CREATE AND AUTO RUN JOBS 7. TOOL SETUP 8. AXIS CALIBRATION (X axis - back gauge, Y1 Y2 axis - ram)

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version MASTEEL PRESSBRAKE TP-700 OPERATING INSTRUCTIONS Always use JOG Mode after changing settings to check bending position. 1.1 Turn on the main power switch on side of electrical cabinet. 1.2 Release the emergency switch on control panel and foot control. 1.3 Make sure all the door switches are closed 1.4 Turn the control power key switch to “ON”. 1.5 Insure that no foreign objects can interfere with brake operation 1.6 Press "Start" to Operate the brake and you will see “NOT REF” flashing. This indicates the Y axis need to...

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version 1.7 Turn on pump. Make sure ram is not all the way up. Press foot pedal to jog the ram down if it is all the way up. And then press Ram up push button and Ram will move up to seize the Y reference position. Once the Y axis reach to reference position, " NOT REF" will disappear, and changed to display "Repeat Ref" “Repeat Reference” is used for recovery of Y axis position when power surge or any other situation causes the Y axis position errors. 1.8 Prepare to bend Note:A full ram stroke cycle includes ram fast approach,...

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version 2. TP-700 CONTROL CONSOLE OPERATION Touch panel display and push buttons Push Button in dark background -- enables programmable control function and displays next control function screen. Programmable Setting Field – touch this key and number pad will display to allow input of desired angle setting. Operating Status Display (display only)

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version Command Keys Description Use this key to enter new data and to acknowledge a message(s). ESC Use this key to abort an edit. Back space. Scrolls the cursor to left. Scrolls the cursor to right Positive and negative Definition of the current setting

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version 3. MAIN CONTROL FUNCTION AND DISPLAY

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version 3.1 Current operating status display : Maximum Brake Capacity X/ R/Y1/Y2: TP 700 has capability of control 4 axis on a press brake. X/R axis are for backguage. X is horizontal backgauge setting and R is Vertical backgauge setting Y1/Y2 is vertical (Ram travel) X-X 4.650: Backstop-X current position in “inches”. R-R 0.000: Backstop-R current position in “inches”. Y-R 11.528: Current Ram Position related to top of bed in “ inches”. 11.528” indicates that mounting surface of the punch is 11.528” above the top surface of...

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version Settings to Program bending angle V : Die opening in "inches". (Refer to Masteel 4-way die specifications) A : Required bending angle in "degrees". Measured at the inside of the bend Å : Bending angle correction in “degrees”. Input "0" on the first test bend. Measure inside bend angle to determine correcting angle required. Input "- (minus) " degrees to correct for under bend : input "+ (plus)” degrees to correct for over bend. T : Material thickness in unit of 0.001" (see bending chart on page 2) : Current Punch Setting

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version 3.2 X/R AXIS POSITION -related to TOOL & Brake configuration X axis Position X axis position is Measured from Ram and Punch load support center to end tip of back gauge finger. The center of load support line is "0" for X axis position. It is fixed with brake configuration of brake There could be 2-4 step of gauge position. Refer to back gauge offset on section 4.4 for work setup R axis Position related to Die and brake table R-R axis position is related to brake table. The top of table is "0" position for R-R axis. It...

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version 3.3 Y AXIS POSITION --related to TOOL & Brake configuration T-Y: Tool Coordinate Y axis Position Tool coordinate Y axis position “T-Y” is relative to TOOLING – punch + die and is defined as the distance measured from the tip of punch to the opening of the die at the bending position. “Zero” position for Tool Coordinate Y axis position is even on the top surface of die. When T-Y is “0” the tip of punch is level with the top of the die opening. A negative T-Y value indicates that the bending position is below the top...

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version TOOL & RAM COORDINATE Y AXIS POSITION

Hydraulic Synchronized CNC Control (TP 700A Control-Y1 Y2 X R) Version 4. GENERAL INTRUDUCTION OF OPERATING CONTROLS 4.1 Function Control Switch Operating Control Panel Pump on push button Power on indicator light NC Control Key switch lock-out Pressure Adjustment (optional) Ram Up Push Button Emergency Stop Switch 4.2 Ram Operating control Foot pedal control functions – Jog Mode – Press foot switch. Ram will jog down; releasing the foot switch will stop the ram in any position in the down stroke. Press Ram Up button to return ram to top of stroke. – Single Stroke Mode – Press & hold foot...