Catalogs >
Marsh Bellofram >
P300 Pressure Regulator

P300 Pressure Regulator
11Pages

Catalog excerpts

• Minimize Sudden Downstream Load Change • Wide Pressure Ranges • P302 has internal relief valve for overpressure protection The P300 series pressure regulator is a manual, direct acting, self-operating, spring loaded, adjustable regulator. The P300 series is used in applications where pressure reduction is required. The regulator will reduce the risk of "shock" from abrupt changes of downstream conditions. This can help prevent safety equipment from shutting an operation down. Applications • Compressors • Gas Engines • Service Regulators Materials of Construction P300 Series Maximum Inlet Pressure P300 Series Range Springs

Open the catalog to page 1

P300 Regulator Rebuild Kits Kit Includes Part Number Diaphragm, Disk Holder, Cap Gasket, O-Ring 971-300-000 * Port orientation is based on the body's "Out" port location in relation to the top view of the regulator. DOWN P300 UP Vent Positions 1 Version Non-Relieving Relieving Configuration Normal High Port Size 1.25 NPT 1.5 NPT 1.5 x 2 NPT 2 NPT Spring Range WC mBAR 3 - 6" WC 9 - 15 5 - 8.5" WC 12 - 21 6 - 14" WC 15 - 35 12 - 28" WC 30 - 70 H Configuration PSIG BAR 1 - 2 PSIG .07 - .14 1.5 - 3 PSIG .10 - .21 2 - 5.5 PSIG .17 - .38 4.5 - 8 PSIG .31 - .55 Special Construction None 150 RF (2"...

Open the catalog to page 2

P300 Head Only Body Size

Open the catalog to page 3

P302 Normal (0) Relief Capacities Outlet Pressure, Outlet Pressure, PSIG PSIG Inlet Pressure, PSIG Inlet Pressure, PSIG Outlet Pressure, Outlet Pressure, PSIG PSIG Inlet Pressure, PSIG 0.5 1" PSIG Set Outlet Pressure 0 Inlet Pressure, PSIG 1" PSIG Set Outlet Pressure

Open the catalog to page 4

P301 & 302 Flow Capacities in SCFH (Nm3/h) of 0.6 Specific Gravity Natural Gas Outlet Pressure, Spring Part Number, and Accuracy Inlet Pressure Orifice Size, Inches (mm) 1 inch WC (2.5 mBAR) droop 1 inch WC (2 mBAR) droop 2 inches WC (5 mBAR) boost 1. Limited due to boost - Shaded areas show where indicated droop would be exceeded regardless of capacity. - Shaded areas show where maximum operating inlet pressure for a given port diameter is exceeded. 128

Open the catalog to page 5

Open the catalog to page 6

P301 & 302 Flow Capacities in SCFH (Nm3/h) of 0.6 Specific Gravity Natural Gas Outlet Pressure, Spring Part Number, and Accuracy 1. Limited due to boost - Shaded areas show where indicated droop would be exceeded regardless of capacity. - Shaded areas show where maximum operating inlet pressure for a given port diameter is exceeded.

Open the catalog to page 7

Open the catalog to page 8

Interchangeability between the BelGAS P200 series and the P300 series The unique feature about the BelGAS P300 regulator is that it utilizes the BelGAS P200 series 1.5”x 2” and the 2” x 2” body using a simple adaptor ring. The simplicity of down-sizing a system when a BelGAS P200 unit is installed is as easy as removing the 2 body-to-head bolts and installing a BelGAS P300 head with the appropriate adaptor and bolts. Or, if a 1.5” x 2” or 2” x 2” BelGAS P300 is installed, the BelGAS P300 head can be removed and a BelGAS P200 head installed to up-size your system. It is important to know, a...

Open the catalog to page 9