Catalogs >
Marsh Bellofram >
Digital Controllers

Digital Controllers
30Pages

Catalog excerpts

DIGITAL CONTROLLERS

The DTC series of PID Controllers offer front panel selection of all operating functions except for some input types. The DTC series offers more flexibility in controls, and more control output options to DigiTec's PID controller line. The DTC offers optional Motorized Valve Control, RS-485 Communication, Heater Current Monitoring, or Remote Setpoint. Auto-tune control will monitor the system output response and after 3 cycles it will automatically calculate and replace the PID constants with optimal process control parameters. Controller Accuracy: For TC inputs: 0.25% of F.S. ±1 degree For...

Open the catalog to page 2

SENSOR TYPE J K T R S C Platinel II SENSOR TYPE SIGNAL INPUTS INPUT TYPE Linear mV Voltage Current TYPE INPUTS FUNCTIONAL SPECIFICATIONS HEAT COOL PID Control Action Cycle Time Deadband PID 0.1 to 100 sec. Programmable from setpoint low limit to setpoint high limit Modes Hysteresis Deviation high/low, Absolute high/low, Band, Sensor Break 0.1 to 99.9 degree RAMP SOAK Ramp Rate Soak Time Soft Start Time OUTPUT SPECIFICATIONS PANEL DISPLAY CONTROL ACTION 1) PID 2) ON-OFF CONTACT RATING (SPST) 5A@230 VAC/ 30 VDC Resistive SSR DRIVE GENERAL SPECIFICATIONS SUPPLY VOLTAGE 85 to 270 V AC/DC (50/60...

Open the catalog to page 3

OVERALL DIMENSIONS Panel Cutout » TERMINAL CONNECTIONS

Open the catalog to page 4

SERIAL COMMUNICATION CONNECTION DIAGRAM / Terminating resistor 1. Maximum 32 slave controllers can be connected to the master 2. The total cable length should not exceed 500 meters. 3. Use shielded twisted -pair cables for RS485 connections. 4. Use terminators having a resistance of 100ohm (1/2 watt) DigiTec Division 800.727.5646 DigiTec Division

Open the catalog to page 5

HMI Panel Display presents the system processes in both text and graphics for the user. Easy to use display provides a custom user interface to the process for both monitoring and system control. From viewing data to making changes to timers and counters, the DigiTec DMT 300 makes it easy. Compatible with PLCs from: • ADC (Dl05) DIMENSIONS (MM) Panel Cutout Panel Display DIN rail installation (standard 35mm) • Allows customer to change the PLC internal status through a programmable key, allowing set point changes. For example: changing alarm setpoints, realtime clock settings, etc. •...

Open the catalog to page 6

Phone Remote Control Real Time Clock Function Network & Monitoring Function Voice Warning FEATURES • Expansion up to 122 I/O (74 Inputs/48 outputs) • Specialty modules for telephone functions and alarming • Optional face mount or panel mount, 4 line display • Free Program Software • Remote Mounting of the HMI Module Programmable Logic Controller • Voice Module (dial out, remote control) • Remote Control (wireless control of 6 inputs) • UL Listed (912A-R and 922D-AR) OPTIONAL ACCESSORIES • Copy Modul • Telephone/Voice Module • Remote Control Transmitter Module • HMI Panel Display (DMT 300)...

Open the catalog to page 7

SPECIFICATIONS MODEL 8 points AC input 8 points DC input (with 6 points analog) 8 points DC input (with 6 points analog) 14 points AC input 14 points DC input (with 8 points analog) 14 points DC input (with 8 points analog) 4 points relay output 4 points relay output 4 points transistor output (equivalent NPN) 8 points relay output 8 points relay output 8 points transistor output (equivalent NPN) With real time clock 12 points AC input 12 points DC input 12 points DC input 8 points relay output 8 points relay output 8 points transistor output (equivalent NPN) 20 Points extended module...

Open the catalog to page 8

The Digitec D2040 loop-powered display is a 3-1/2 Digit, short depth LCD display. The display can indicate level, % flow, or pressure in a 4-20 mA process loop. The D2040 also is well suited to be used as a remote display. User adjustable scale (gain), offset and decimal point allow immediate calibration of measurement being displayed. PROCESS APPLICATIONS • Level • Pressure • Flow 3-1/2 Digit Loop-Powered Meter Current loop measurement of 4-20mA and 10-50mA DISPLAY RANGE • 3-1/2 Digit full-size LCD 0.6" high • 1/8 DIN Anodized Aluminum Case POWER REQUIREMENTS Loop powered; voltage drop...

Open the catalog to page 9

The Digitec D2080 is a loop powered indicator that measures, displays and totalizes the current in a 4-20 mA circuit. Although the instrument is loop powered, it only produces <3.5 V drop allowing it to be used in series with almost any 4-20 mA application. Modular accessories enable the user to select the lowest cost configuration while retaining full interchangeability between instruments. Optional high alarms provide two isolated open drain outputs which may be independently programmed with a high trip point. When an alarm is tripped, the alarm and current reading alternate on the...

Open the catalog to page 10

The Digitec D2090 3-1/2 Digit, loop-powered indicator is perfect for process applications where no power is available, a NEMA 4X enclosure is needed and cost is a consideration. Designed for easy installation, the two wire connection is all that is required to power and operate the unit. The D2090 can be wall or panel mounted. The Digitec D2095 4-1/2 Digit, loop-powered indicator is perfect for process applications where no power is available, and a NEMA 4X enclosure is needed. Designed for easy installation, the two wire connection is all that is required to power and operate the unit. The...

Open the catalog to page 11

The DigiTec D3700A series digital panel meters are available as either the single-channel D3720A or the dual-channel D3722A. These full- featured meters include a 6-digit LED display, a user-friendly configuration menu and high-speed measurement rate for the most demanding applications. Combine all of this with its clean appearance, industrialized aluminum case, NEMA 4X construction and snap-action buttons and you have a meter ready for all applications. 3 Types of Calibration: USER - calibration allows the entry of the low and high input values and the corresponding low and high display...

Open the catalog to page 12

UP Arrow Key: Increases the current value of the flashing digit by one unit per press. • Assignable to any channel • Programmable for high or low limit DOWN Arrow Key: Decreases the current value of the flashing digit by one unit per press. • Programmable setpoint value • Programmable hysteresis for complete display range EXIT Key: Returns you to RUN mode when at main menu or returns you to main menu prompt when in programming menu. • Programmable to Flash Display on alarm • Alarm #1 is programmable for fail safe operation for all the alarms. (Fail safe operation allows the relay to...

Open the catalog to page 13