Single axis Laser Micrometers for very high accuracy diameter measurement Vertical Measuring Field Side Measuring Field (1) Measurable Diameters Resolution (Selectable) Linearity (Centred Product) Linearity (in the Meas. Plane) (5) Side Linearity (6) Repeatability (T=1s, ±2σ) (7) Beam Spot Size (s,l) (8) (mm) Side Dither of the Scanning Plane (Hz) Scanning Frequency (m/s) Scanning Speed (µm/mm°C) Thermal Coefficient (9) Power Supply Laser Source (mm) Dimensions (10) (kg) Weight (10) (°C) Operating Temperature Range (°C) Storage Temperature Atmosferic Humidity (m) Altitude Protection D00104_E rev. 1,9 - 02.10.2023 - Copyright © 2007-2023 Aeroel s.r.l. - All rights reserved Two standard models are available for the XLS80 and XLS150 sensors: the first with head gap 200 and 430 mm and the second with head gap 300 and 630 mm. (1) Maximum allowed side displacement of the part axis. (2) For Ø ≤ 25 mm. For Ø > 25 mm the linearity is ± 0.75 µm. The value is inclusive of the Aeroel’s masters uncertainty (± 0.3 µm) (3) For Ø ≤ 40 mm. For Ø > 40 mm the linearity is ± 1.5 µm. The value is inclusive of the Aeroel’s masters uncertainty (± 0.3 µm) (4) For Ø ≤ 70 mm. For Ø > 70 mm the linearity is ± 5 µm. The value is inclusive of the Aeroel’s masters uncertainty (± 0.3 µm) This product conforms to the following standards: 21 CFR 1040.10 (USA) • CEI EN-60825-1:2014 (EU) ( ) Maximum error, when a master is moved in the measuring plane, checked with Ø = 8 mm (XLS40), Ø = 20 mm (XLS80) or Ø = 38 mm (XLS150). The measuring plane is located halfway between transmitter and receiver. Ultra accurate, high speed Laser Gauges for contact-less diameter measurement, featuring built-in electronics and Ethernet/Rs232/Rs485 interface • • • • • • • • • • • • • • Up to 150 mm measuring range Multiple measuring modes and types Up to 0.07 µm repeatability 1500 Hz scanning frequency Outstanding single shot repeatability Excellent linearity Permanent self calibration Fully re-programmable Direct connection to PC, PLC e NC Motor with Fluid Dynamic Bearing Technology NO-VAR: active thermal compensation Direct connection to Internet Browser Capability to store different application programs Inputs for reading and synchronizing quadrature encoders It’s an ideal Intelligent Diameter Sensor for the on-line control of products like: (6) Maximum error, for a side displacement of the master out of the measuring plane. (7) Single shot repeatability (± 2σ) is ± 1.5 µm (XLS40), ± 3.5 µm (XLS80) and ± 5 µm (XLS 150) (8) Elliptical spot: “s” is the thickness and “l” is the width. (9) This is the measuring error due to a change in the ambient temperature when measuring a part with zero thermal expansion coefficient (INVAR). This is specified for gauges using a software PRESET for the NO-VAR option and when the rate of change of the ambient temperature is lower than 3°/h. When the NO-VAR option is ENABLED, the gauge thermal expansion coefficient is programmable by the user. (10) The connecting cable is not included. The figures between brackets are related to the model with head separation 300 mm (XLS80) or 630 mm (XLS150). Specifications subject to change without notice AEROEL SRL - Via Pier Paolo Pasolini, 35/3 - 33040 Pradamano (UD) ITALY - tel. +39 0432671301 - fax +39 0432671543 - [email protected] - https://www.aeroel.it Ground or turned parts Metal tub

Exclusive Aeroel features The XLS sensors are equipped with a pre-loaded software to perform different types of measurements and in several modes, to meet a number of applications. In general the instrument performs just as an Intelligent Sensor, transmitting the measured data to an external device, through its serial ports. The tolerance checking or other more sophisticated features are not included, these are performed by the user’s device or by the available Aeroel Dedicated Systems. • The NO-VAR option allows you to automatically compensate for the expansion of the part when room temperature...