1. Catalogs
  2. MARPOSS
  3. TABLE-GAUGE X

TABLE-GAUGE X
1 /4Pages

TABLE-GAUGE X

TABLE-GAUGE X
1 /4Pages

Catalog excerpts

TABLE-GAUGE X-1

Use the Xactum Intelligent Laser Gauges as bench-top micrometers, in the Table-Gauge configuration: with no other instrument can you measure diameters so quickly, so accurately and so easily. It’s the ideal instrument to check pins, ground or other turned parts. No matter what the operators’ skill level! Ultra-accurate and perfectly reproducible measurements thanks to Aeroel’s outstanding Laser Technology offered at affordable conditio

 Open the catalog to page 1
TABLE-GAUGE X-2

The Table-Gauge.X The XLS gauges are programmed with a dedicated software and are completed with a display unit, a remote control, fixturing to hold the part and a base-plate for bench-top use: using this “Table-Gauge” assembly you can, in a few seconds, check the diameter, roundness and the concentricity of ground or turned parts, to an accuracy that before only could be obtained in a metrology room, by using much more expensive equipment and specialized personnel. Exclusive Aeroel features • The scanning motor based on the Fluid Dynamic Bearing technology, without ball bearing works perfectly,...

 Open the catalog to page 2
TABLE-GAUGE X-3

Measurement examples Diameter and roundness: rotate the part by 180° and measure the diameter, display the average diameter and the value of the Diameter Range = Dmax-Dmin. Run-out: measure of the center position during a 180° rotation, with the part held between centers, and display the value of the Center Position Range = Cmax-Cmin. You will get the run out of the measured section referred to the center axis. Sphere er Groove diameter: move the part along its axis and measure the diameter, display the Maximum or Minimum Diameter value. Display and remote control Multicolor LED display to show...

 Open the catalog to page 3
TABLE-GAUGE X-4

All dimensions are in mm and do not consider cables and connectors. DISPLAY AND ALARMS MODULE DM-200 Main Display LED 6 digits, 7 segments multicolour Sub Display LED 2 digit 6 Warning lights for the Status of the Inputs and the Outputs 4 Outputs protected PNP, Imax: 100 mA 2 Inputs PNP, Ityp.: 15 mA Optional analog output: ± 10 V Dimensions: 97 x 49 x 105 mm Weight: 0.3 kg Power supply: 24 VDC 150 mA D00092_E rev. 1,9 - 06.07.2022 - Copyright © 2006-2022 Aeroel s.r.l. - All rights reserved Size: 180 x 50 x 26 mm Weight: 80 g (without batteries) Power supply: 2 AAA 1.5 V batteries Available models...

 Open the catalog to page 4

All MARPOSS catalogs and technical brochures

  1. MPLS SERIES

    2  Pages

  2. M62 FLEX

    2  Pages

  3. M62

    8  Pages

  4. 2SEAL

    2  Pages

  5. M50

    2  Pages

  6. OPTOQUICK

    20  Pages

  7. M39S

    4  Pages

  8. QUICK SET LINE

    20  Pages

  9. QUADRALINE XY

    4  Pages

  10. MECLAB X

    4  Pages

  11. XLS.X PLUS

    2  Pages

  12. XLS XY PLUS

    4  Pages

  13. HESNIFFER

    2  Pages

  14. HESAVER

    2  Pages

  15. T2

    2  Pages

  16. TM3PQ

    2  Pages

  17. UNISENSE GO

    2  Pages

  18. LABSENSE

    2  Pages

  19. MULTISENSE

    2  Pages

  20. UNISENSE C

    2  Pages

  21. Unisense O

    2  Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.