Plug & TestTM Adapter Model PTA

Product catalog summary

Overview: The document is a data sheet for the Plug & Test^TM Adapter Model PTA by Mark-10 Corporation. It provides specifications, features, and requirements for connecting strain gage-based load cells, force sensors, and torque sensors to Mark-10 indicators (Models 7i, 5i, and 3i).

Specifications: The adapter allows for user-configurable programming of sensor capacity and resolution via a software utility. It supports force capacities from 0.12 to 750,000 lbF (0.5 N to 4,000 kN) and torque capacities from 10 ozFin to 40,000 lbFft (7 Ncm to 57,000 Nm). Configuration and calibration data are stored within the adapter, enabling sensor interchangeability.

Features: The adapter is compatible with strain gage-based sensors and includes a screw terminal block for easy sensor wire connection. It can be programmed via USB or RS-232 through the indicator and comes with a strain relief, user-writeable identification label, and a Resource CD with software.

Requirements: The adapter requires a full bridge sensor type with a resistance of 300 - 1000 ohms and sensitivity of 1 - 3 mV/V full scale. It is compatible with Mark-10 indicators with firmware version 1.0.9 or later. Older versions can use the adapter but cannot calibrate single-direction load cells.

Force and Torque Capacities: The document includes detailed tables of force and torque capacities and resolutions for different models of indicators. These tables specify the capacity and resolution in various units such as lbF, ozF, kgF, gF, N, kN, and others, providing precise measurement capabilities for different applications.

Catalog excerpts

Plug & TestTM Adapter Model PTA Page 1 of 3 Connect common strain gage-based load cells, force sensors, and torque sensors to our Models 7i, 5i and 3i indicators with this user-configurable adapter and software. Sensor capacity and resolutions may be programmed via an included software utility, which includes a library of common force capacities from 0.12 to 750,000 lbF (0.5 N to 4,000 kN), and torque capacities from 10 ozFin to 40,000 lbFft (7 Ncm to 57,000 Nm). An identification number may be programmed, which is displayed upon indicator power-up or the indicator’s Information screen. Through Plug & TestTM technology, all configuration and calibration information is saved within the adapter. This flexibility allows for interchangeability between multiple sensors with any Mark-10 indicator. Features  Compatible with strain gage-based load cells, force sensors, and torque sensors  Screw terminal block allows for easy connection of sensor wires  Software conﬁguration utility is included, for easy programming of sensor capacity, resolution, and identiﬁcation number  Program the adapter via USB or RS-232 through the indicator  Supplied with a strain relief, user-writeable identiﬁcation label, and Resource CD with software Requirements  Sensor type: Full bridge  Sensor resistance: 300 - 1000 ohms  Sensor sensitivity: 1 - 3 mV/V full scale  Mark-10 indicator with ﬁrmware version 1.0.9 or later* ^Cover is removed to expose the PCB with labelled wire connections and screw terminal block. * The PTA adapter cannot be configured using older indicator versions. The PTA adapter can be used with older indicator versions, however, the adapter cannot be calibrated for single-direction load cells, such as load button and thru hole type load cells. ^Software utility features a library of force and torque capacities. Programming of capacity, resolution, and identification number is done via USB through any Mark-10 indicator. Mark-10 Corporation  www.mark-10.com  [email protected] Toll-free: 888-MARK-TEN  Tel: 631-842-9200  Fax: 631-842-9201 Specifications subje

Open the catalog to page 1

Plug & Test™ Adapter Model PTA Page 2 of 3 Force Capacities & Resolutions Resolution With Model 7i / 5i indicatorResolution With Model 3i indicator IbF ozF kgF gF N kN mN Specifications subject to change without prior notice

Open the catalog to page 2