8000-1
24Pages

Catalog excerpts

Grove Manitowoc National Crane Potain Product Guide • 525 fpm maximum line speed • 17,000 lb rated line pull

Outline dimensions Winch performance data 12 Load chart notes 13 Heavy-lift boom range / charts 16 Fixed jib boom range/charts 18 Manitowoc Crane Care 22

Open the catalog to page 3

Specifications Upperworks Engine HINO J08E-UV, 6 cylinder, water-cooled diesel, direct fuel injection with turbocharger, 285 HP at 2100 high-idle RPM. Maximum torque 750 lb•ft net at 1,600 rpm; Interim Tier 4/Stage IIIB (Required for sale in the US/Canada/Europe; requires "Ultra Low Sulfur Diesel") One diesel fuel tank, 105 gallons capacity. Cooling: Oil-to-air heat exchanger (plate-fin type). Filtration: Full-flow and bypass type with replaceable paper element. Drums Front and rear drums for load hoist powered by variable displacement piston-type motors, driven through planetary reducers....

Open the catalog to page 4

Specifications Wire Rope Capacity: Drum 492 ft working length. Line speed: Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 ft/min Lowering. . . . . . . . . . . . . . . . . . . . . . . . . . . 230 ft/min Gantry This high folding type gantry is fitted with a sheave frame for boom hoist reeving. Hydraulic lift is standard. It provides full up, full down positions. are built into the crawler side frame within the shoe width. The track rollers are sealed for maintenance-free operation. Crawler shoes 36" wide crawler. Travel speed (High/Low) 1.07/0.71 mph Counterweight Upper...

Open the catalog to page 5

90 USt hook block, 2,892 lb with five 24" Nominal O.D. roller bearing sheaves. Optional: Detachable upper boom point with one 561 mm Nominal O. D. roller bearing steel sheave grooved for 22 mm rope for liftcrane. Working weight Approximately 165,600 lb including upperworks and lowerworks, full upper counterweights, full carbody counterweights and 50 ft basic boom. Ground pressure Approximately 10.8 psi with basic boom. Gradebility With basic boom: 40%.

Open the catalog to page 6

Outline dimensions

Open the catalog to page 7

Outline dimensions Note: Weight includes base machine, crawler, gantry, maximum hoist and whip lines on drums, boom butt, full hydraulic fluid reservoir, and one third tank of fuel. Note: Weight includes base machine, crawler, gantry, maximum hoist and whip lines on drums, full hydraulic fluid reservoir, and one third tank of fuel. Upperworks without crawlers xl Note: Weight includes base machine, gantry, maximum hoist and whip lines on drums, boom butt, full hydraulic fluid reservoir, and one third tank of fuel. Upperworks without crawlers xl Note: Weight includes base machine, gantry,...

Open the catalog to page 8

Outline dimensions Carbody counterweight Self removal unit

Open the catalog to page 9

Outline dimensions Note: Use one "A " type insert with lug required for any boom combinations that require a 4(f insert.

Open the catalog to page 10

Outline dimensions Fixed jib top Length Width Height Weight Length Width Height Weight Length Width Height Weight Length Width Height Weight

Open the catalog to page 11

Winch performance data Line pull Rated line pull lb *Maximum line pull Front drum Rear drum Optional 3rd drum * Maximum line pull is not based on wire rope strength. Wire rope specifications Use Front drum Boom hoist drum Rear drum Front and rear winch Line speed ft/min 1 Rated line pull Single line pull lb NOTE: Line speeds and line pull based on single line. Line pulls are not based on wire rope strength.

Open the catalog to page 12

Load chart notes 1. Rated loads included in the charts are the maximum allowable freely suspended loads at a given boom length, boom angle and load radius, and have been determined for the machine standing level on firm supporting surface under ideal operating conditions.The user must limit or de-rate rated loads to allow for adverse conditions (such as soft or uneven ground, out-of-level conditions, wind side loads, pendulum action, jerking or sudden stopping of loads, inexperience of personnel, multiple machine lifts, and traveling with a load). 2. Capacities do not exceed 75% of minimum...

Open the catalog to page 13

Boom combinations No. 8000-1 heavy-lift boom combinations Boom inserts Boom length ft * NOTE: One 40 ft boom insert with lug 40A is required for fixed jib. When no jib is installed a 40 ft boom can be used instead of 40A. Model 8000-1 main boom 200 ft 10 ft boom insert 10 ft boom insert 19 ft boom butt Model 8000-1 Main boom 200 ft

Open the catalog to page 14

Boom combinations No. 8000-1 fixed jib combinations Fixed jib inserts Fixed jib length ft 40 ft boom insert Model 8000-1 main boom 190 ft 10 ft boom insert 19 ft boom butt Model 8000-1 Fixed jib on main boom 250 ft

Open the catalog to page 15

Heavy-lift boom range diagram No. 8000-1 main boom Height above ground ft Distance from centerline of rotation ft

Open the catalog to page 16

Heavy-lift boom load charts Model 8000-1 liftcrane boom capacities - 8000-1 main boom 57,584 lb crane counterweight 14,330 lb carbody counterweight crawler extended 360° Rating Boom ft For complete chart, refer to www.cranelibrary.com. Meets ASME B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.

Open the catalog to page 17

Fixed jib range diagram No. 8000-1 fixed jib on main boom Height above ground ft Distance from centerline of rotation ft

Open the catalog to page 18

Fixed jib load charts Model 8000-1 liftcrane jib capacities No. 8000-1 fixed jib on main boom 57,584 lb crane counterweight, 14,330 lb carbody counterweight crawler extended 360° Rating For complete chart, refer to www.cranelibrary.com. Meets ASME B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.

Open the catalog to page 19

Open the catalog to page 20

Clamshell Boom: Welded lattice construction using tubular, high-tensile steel chords with pin connections between sections. Basic boom length: 50 ft Max. boom length: 70 ft Limit on clamshell bucket weight: (4,600 lb) Maximum component chart Boom length ft Boom arrangement Base-A-A-Tip, Base-B-Tip GUIDE SHEAVE Figures represent maximum allowable capacity, and assume level ground and ideal working conditions. Capacities are calculated at 66% of the minimum tipping loads. Capacities are maximum recommended by PCSA Standard #4. Allowances must be made by the user for such unfavorable...

Open the catalog to page 21