Manitowoc 12000-1 Product Guide ASME B30.5 Metric / Imperial Features • 110 t (120 USt) capacity • 70,1 m (230 ft) heavy-lift boom • Max boom + jib combination: 61 m (200 ft) + 21,3 m (70 ft) • 213 kW (285 HP) engine • 163 m/min (525 fpm) maximum line speed • 110 kN (25,000 lb) rated line pull

Energy saving systems Green-Engine mode conserves fuel during full speed drum operation under load, at a lower engine RPM. Other available options include Green-Winch Mode and Auto Idling Stop Mode. Self-erecting counterweight Eliminates the need for an assist crane, and also allows for reduced counterweight chart operation. Retractable crawlers Crawlers can be extended and retracted for better jobsite maneuverability. On some models, these crawlers can also ship attached for easier transport and quicker setup.

Load chart notes 13 Main boom range / load charts 16 Fixed jib range / load charts 18 Manitowoc Crane Care 22

Specifications Upperworks Engine HINO J08E-UV, 6 cylinder, water-cooled diesel, direct fuel injection with turbocharger, 213 kW (285 HP) at 2100 high-idle RPM. Maximum torque 1017 N•m (750 lb•ft) net at 1,600 rpm; Interim Tier 4/Stage IIIB (Required for sale in the US/Canada/Europe; requires "Ultra Low Sulfur Diesel") Maximum pressure rating. . . . . 31.9 MPa (4,630 psi) Load hoist and propel. . . . . . . . . . . . . . . . 2 Piston pumps Boom hoist. . . . . . . . . . . . . . . . . . . . . . 1 Piston pump Swing . . . . . . . . . . . . . . . . . . . . . . . . 1 Piston pump Control system and auxiliary....

Specifications Rotating bed turntable: Single-row ball bearing with an integral internally cut swing gear. Swing speed: 3.2 rpm Boom support system Single drum powered by a hydraulic axial piston motor through a planetary reducer. Brake: A spring-set, hydraulically released multipledisc brake is mounted on the boom hoist motor. An external ratchet is fitted for locking the drum. Drum: Single drum, grooved for 20 mm diameter wire rope. Boom Hoist reeving is 10-part line. Wire Rope Capacity: Drum 155 m (508 ft) working length. Line speed: Single line on the first drum layer Hoisting:. . . . . ....

70 t hook block, 900 kg, with three 500 mm Nominal O.D. roller bearing sheaves. (90 USt hook block, 4,060 lb, with three 24" Nominal O.D. roller bearing sheaves.) Welded lattice construction using tubular, high-tensile steel chords with pin connections between sections. Boom tip is open throat construction. Two idler sheaves and four point sheaves are standard. 110 t hook block, 1700 kg, with five 500 mm Nominal O.D. roller bearing sheaves. (120 USt hook block, 3,760 lb with five 24" Nominal O.D. roller bearing sheaves.) Basic boom length 15,2 m (50') consists of the boom butt section 7,62 m...

Outline dimensions (CRAWLER RETRACTED) (CRAWLER EXTENDED)

Outline dimensions Upperworks Length Width Height Weight Note: Weight includes base machine, crawler, gantry, maximum hoist and whip lines on drums, boom butt, full hydraulic fluid reservoir, and one third tank of fuel. Length Width Height Weight Note: Weight includes base machine, crawler, gantry, maximum hoist and whip lines on drums, full hydraulic fluid reservoir, and one third tank of fuel. Upperworks without crawlers Length Width Height Weight Note: Weight includes base machine, gantry, maximum hoist and whip lines on drums, full hydraulic fluid reservoir, and one third tank of fuel. Upperworks...

Outline dimensions Hydraulic jack (if removed) Length Width Height Weight Length Width Height Weight Length Width Height Weight Length Width Height Weight Carbody counterweight with float Length Width Height Weight Carbody counterweight without float x 1 Length Width Height Weight

Outline dimensions Note: Use of one "A" type insert with lug required for any boom combinations that require a 12,2 m (40') insert.

Outline dimensions

Performance data Line pull Rated line pull kg (lb) *Maximum line pull Front drum Rear drum * Maximum line pull is not based on wire rope strength. Wire rope specifications Working length m (ft) Boom hoist drum Third drum (optional) Front drum Rear drum Front and rear winch performance (optional: third winch) Line speed m/min (ft/min) 1 Layer Single line pull kg (lb) NOTE: Line speeds and line pull based on single line. Line pulls are not based on wire rope strength.

Load chart notes 1. Rated loads included in the charts are the maximum allowable freely suspended loads at a given boom length, boom angle and load radius, and have been determined for the machine standing level on firm supporting surface under ideal operating conditions.The user must limit or de-rate rated loads to allow for adverse conditions (such as soft or uneven ground, out-of-level conditions, wind, side loads, pendulum action, jerking or sudden stopping of loads, inexperience of personnel, multiple machine lifts, and traveling with a load). 2. Capacities do not exceed 75% of minimum tipping...

Boom combinations No. 12000-1 heavy-lift boom combinations Boom inserts Boom length m (ft) * NOTE: One 40 ft (12,2 m) boom insert with lug 40A is required for fixed jib. When no jib is installed a 40 ft (12,2 m) boom can be used instead of 40A. Model 12000-1 main boom 70,1 m (230 ft) 3,0 m (10 ft) boom insert 3,0 m (10 ft) boom insert Model 12000-1 Main boom 70,1 m (230 ft)

Boom combinations No. 12000-1 fixed jib combinations Fixed jib inserts Fixed jib length m (ft) Model 12000-1 main boom 61,0 m (200 ft) Model 12000-1 Fixed jib on main boom 82,3 m (270 ft)

Heavy-lift boom range diagram No. 12000-1 main boom Height above ground m (ft)

Heavy-lift boom load charts Model 12000-1 liftcrane boom capacities - 12000-1 main boom 34 600 kg (76,280 lb) crane counterweight, 6 500 kg (14,330 lb) carbody counterweight crawler extended Meets ASME B30.5 Requirements – Capacities do not exceet 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes. For complete chart, refer to www.cranelibrary.com. Meets ASME B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.