Catalogs >
Manitowoc Cranes >
10000A-1

10000A-1
24Pages

Catalog excerpts

Grove Manitowoc National Crane Potain Product Guide • 535 fpm maximum line speed • 25,200 lb rated line pull

Self-erecting counterweight Eliminates the need for an assist crane, and also allows for reduced counterweight chart operation. Retractable crawlers Crawlers can be extended and retracted for better jobsite maneuverability. On some models, these crawlers can also ship attached for easier transport and quicker setup. Energy saving systems Green-Engine mode conserves fuel during full speed drum operation under load, at a lower engine RPM. Other available options include Green-Winch Mode and Auto Idling Stop Mode.

Open the catalog to page 2

Outline dimensions Winch performance data 13 Load chart notes Heavy-lift boom range / charts 16 Fixed jib boom range / load charts 18 Manitowoc Crane Care 22

Open the catalog to page 3

Specifications Upperworks Engine HINO J08E-UV, 6 cylinder, water-cooled diesel, direct fuel injection with turbocharger, 285 HP at 2100 high-idle RPM. Maximum torque 750 lb•ft net at 1,600 rpm; Interim Tier 4/Stage IIIB (Required for sale in the US/Canada/Europe; requires "Ultra Low Sulfur Diesel") One diesel fuel tank, 105 gallons capacity. Two 12 volt 136 AH capacity batteries, 24 volt system and 90 amp alternator. All wiring harnesses and connectors are numbered for easier servicing. Machine is equipped with individual fused branch circuits. Controls Full-flow hydraulic control system...

Open the catalog to page 4

Specifications Line speed: Single line on first drum layer. Hoisting . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 ft/min Lowering. . . . . . . . . . . . . . . . . . . . . . . . . . . 230 ft/min Gantry This high folding type gantry is fitted with a sheave frame for boom hoist reeving. It provides full up, full down positions. Counterweight a planetary gearbox. Hydraulic motor and gear box are built into the crawler side frame within the shoe width. The track rollers are sealed for maintenance-free operation. Crawler brakes: multiple disk type, spring set hydraulically released...

Open the catalog to page 5

12 USt all hook, 722 lb wedge socket for 26 b mm wire rope. 50 USt hook block, 2,311 lb with three 24" Nominal O.D. roller bearing sheaves. 75 USt hook block, 3,820 lb, with four 24" Nominal O.D. roller bearing sheaves. 100 USt hook block, 2,946 lb with four 24" Nominal O.D. roller bearing sheaves. Optional: Detachable upper boom point with one 575 mm Nominal outer diameter roller bearing steel sheave grooved for 26mm rope for liftcrane. Machine inclination sensor. Swing angle detection and angle limiter. Counterweight detection. Hydraulic tagline. External lamp for overload alarm. Working...

Open the catalog to page 6

Outline dimensions (CRAWLER RETRACTED) (CRAWLER EXTENDED)

Open the catalog to page 8

Outline dimensions Note: Weight includes base machine, crawler, gantry, maximum hoist and whip lines on drums, boom butt, full hydraulic fluid reservoir, and one third tank of fuel. Note: Weight includes base machine, crawler, gantry, maximum hoist and whip lines on drums without self-removal unit, full hydraulic fluid reservoir, and one third tank of fuel. Upperworks without crawlers Note: Weight includes base machine, gantry, maximum hoist and whip lines on drums, boom butt, full hydraulic fluid reservoir, and one third tank of fuel. Upperworks without crawlers Note: Weight includes base...

Open the catalog to page 9

Outline dimensions Upper counterweight Carbody counterweight

Open the catalog to page 10

Self removal unit Length Width Height Weight Length Width Height Weight Length Width Height Weight Length Width Height Weight Length Width Height Weight Length Width Height Weight Note: Use one "A" type insert with lug required for any boom combinations that require a 40 ' insert.

Open the catalog to page 11

Outline dimensions Fixed jib butt Length Width Height Weight Length Width Height Weight Length Width Height Weight Length Width Height Weight Length Width Height Weight

Open the catalog to page 12

Winch performance data Line pull Rated line pull lb *Maximum line pull Front drum Rear drum * Maximum line pull is not based on wire rope strength. Wire rope specifications Diameter mm Rear drum Boom hoist drum Front drum Front and rear winch Line speed ft/min 1 Rated line pull Single line pull lb NOTE: Line speeds and line pull based on single line. Line pulls are not based on wire rope strength.

Open the catalog to page 13

Load chart notes 1. Rated loads included in the charts are the maximum allowable freely suspended loads at a given boom length, boom angle and load radius, and have been determined for the machine standing level on firm supporting surface under ideal operating conditions.The user must limit or de-rate rated loads to allow for adverse conditions (such as soft or uneven ground, out-of-level conditions, wind side loads, pendulum action, jerking or sudden stopping of loads, inexperience of personnel, multiple machine lifts, and traveling with a load). 2. Capacities do not exceed 75% of minimum...

Open the catalog to page 14

Boom combinations No. 10000A-1 heavy-lift boom combinations No. 10000A-1 fixed jib combinations Fixed jib inserts Boom inserts Boom length ft 40 ft boom insert 40 ft boom insert * NOTE: One 40 ft boom insert with lug 40A is required for fixed jib. When no jib is installed a 40 ft boom can be used instead of 40A. 40 ft boom insert 40 ft boom insert Model 10000A-1 main boom 190 ft Model 10000A-1 main boom 200 ft 40 ft boom insert 40 ft boom insert 10 ft boom insert 10 ft boom insert 19 ft boom butt Model 10000A-1 Main boom 200 ft 10 ft boom insert 19 ft boom butt Model 10000A-1 Fixed jib on...

Open the catalog to page 15

Heavy-lift boom range diagram No. 10000A-1 main boom Height above ground ft Distance from centerline of rotation ft

Open the catalog to page 16

Heavy-lift boom load charts Model 10000A-1 liftcrane boom capacities – 10000A-1 main boom 69,000 lb upper counterweight + 31,750 lb carbody counterweight 360° Rating Boom ft 120 130 140 150 160 165 *Rated loads based on factors other than machine stability such as structural competence. For complete chart, refer to www.cranelibrary.com. Meets ASME B30.5 Requirements - Capacities do not exceed 75% of static tipping load. NOTICE: This capacity chart is for reference only and must not be used for lifting purposes.

Open the catalog to page 17