Catalogs >
MAGTROL >
DSP 7000 | High-Speed Programmable Controller

DSP 7000 | High-Speed Programmable Controller
9Pages

Catalog excerpts

DSP 7000 | High-Speed Programmable Controller - 1

PROGRAMMABLE CONTROLLER FEATURES ▪▪ DSP7001 Single Channel: Low cost and easy to use ▪▪ DSP7002 Dual Channel: Enables the support of two testing instruments with independent or tandem configurations and two fully independent control loops ▪▪ Built-in Alarm System: For power, speed, torque, temperature, air flow, water flow, electrical overload and external inputs ▪▪ High Speed Data Acquisition: Up to 500 torque and speed points per second of both channels with time stamp ▪▪ High Quality, Easy-to-Read Vacuum Fluorescent Readout: Displays torque, speed, power, auxiliary and PID (proportional gain, integral and derivative) values ▪▪ Fast Full-Curve Data Acquisition: Free-run to locked rotor in seconds ▪▪ Speed & Torque Operating Modes: PID settings for exceptional dynamometer control ▪▪ Programmable Digital PID Values: Controlled and stored via M-Test Software or controlled manually ▪▪ Built-in Current-Regulated Supply: For use with Hysteresis Dynamometer or brakes up to 1amp ▪▪ Adjustable Torque Units: English, Metric and SI are standard ▪▪ Digital Filter: Removes undesired noise from torque signals ▪▪ Saving: Currently used configuration can be saved and recalled at power up ▪▪ Single or Multi-point Torque and Speed Stabilized Testing: Via M-TEST 7.0 Software ▪▪ Closed Box Calibration ▪▪ Rack Mounting: 19" (482.6 mm) with handles ▪▪ Backwards Compatible: Compatible with the DSP6001 (in DSP6001 mode) ▪▪ HD5 dynamometers: Supported ▪▪ USB: Standard ▪▪ Low RPM: calculation from angle (quadrature signal) and time designed to capture RPM’s as low as .001 RPM ▪▪ Position Measurement: Two quadrature decoders Fig.1 : DSP7000 Series Programmable Controller OPTIONS ▪▪ Interfaces: RS-232 and IEEE-488 ▪▪ I/O card accessible programmatically (LabVIEW™, Visual C) DESCRIPTION Magtrol’s Model DSP7000 High Speed Programmable Dynamometer Controller employs state-of-the-art Digital Signal Processing Technology to provide superior motor testing capabilities. Designed for use with any Magtrol Hysteresis, Eddy-Current or Powder Dynamometer, Magtrol In-Line Torque Transducer or auxiliary instrumentation, the DSP7000 can provide complete PC control via the USB or optional IEEE-488 or RS-232 interface. With up to 500 readings per second, the DSP7000 is ideally suited for both the test lab and the production line. APPLICATIONS In the laboratory, the DSP7000’s high sample rate provides superior resolution for data acquisition and curve plotting. This allows for capturing more usable motor test data during switching, breakdown and other transitional areas of the motor test curve. For production and incoming inspection, the DSP7000 displays torque, speed and power at all times, allowing the Controller to be used as a manual stand alone unit or as part of a complete PC system. © 2018 MAGTROL | Due to continual product development, Magtrol reserve

Open the catalog to page 1

DSP 7000 | High-Speed Programmable Controller - 2

H MAGTROL MOTOR TESTING SOFTWARE Magtrol's M-TEST 7 Software (sold separately) is a state-of-the-art motor testing program for Windows®-based data acquisition. Used with the Magtrol DSP7000 Controller, Magtrol M-TEST 7 Software provides the control of any Magtrol Dynamometer and runs test sequences in a manner best suited to the overall accuracy and efficiency of the Magtrol Motor Test System. The data that is generated by Magtrol's Motor Testing Software can be stored, displayed and printed in tabular or graphic formats, and can be easily imported into a spreadsheet. Written in LabVIEW™,...

Open the catalog to page 2

DSP 7000 | High-Speed Programmable Controller - 3

H MAGTROL OPTIONAL EQUIPMENT COMMUNICATIONS RS-232 Interface The RS-232 Interface provides backwards compatibility for older systems. 300, 600, 1200, 2400, 4800, 9600, 19200 and 115200 Baud rates are supported. GPIB IEEE-488 Interface The GPIB IEEE-488 Interface provides standard GPIB communications. I/O CARD ■ Torque/Speed Analog Outputs: For interface with a data acquistion system ■ Analog Signal such as tachometer can be routed to PID loop ■ External alarm input ■ Alarm relay contacts ■ 2 Relays ■ 3 Digital inputs ■ 2 Digital outputs ■ 2 Analog inputs ■ 2 Analog outputs ■ 5 Volts...

Open the catalog to page 3

DSP 7000 | High-Speed Programmable Controller - 4

DSP7000 SERIES REAR PANELS For use with any Magtrol Dynamometer (Hysteresis, Eddy-Current, Powder Brake), Magtrol Torque Transducer • USB (standard) and Optional GPIB/IEEE-488 Interface or RS-232 Interface for Connection to PC (GPIB Shown) Connector for Model DES Power Supplies (for WB/PB and HD 825 Dynamometers only) For use with any Magtrol Dynamometer (Hysteresis, Eddy-Current, Powder Brake), Magtrol Torque Transducer Optional I/O Card 1 and I/O Card 2 Connectors for Models DES Power Supplies (for WB/PB and HD 825 Dynamometers only) • • USB (standard) and Optional GPIB/IEEE-488 Interface...

Open the catalog to page 4

DSP 7000 | High-Speed Programmable Controller - 5

DSP7000 SERIES SYSTEM CONFIGURATIONS Hysteresis Dynamometer (HD) Motor Under Test AC Mains DSP7001 CONNECTED TO HYSTERESIS DYNAMOMETER Hysteresis Brake (<1 Amp) OR Hysteresis Brake (<5 Amp)/ Eddy-Current/ Powder Brake DSP7001 CONNECTED TO A HYSTERESIS OR EDDY-CURRENT/POWDER BRAKE WITH IN-LINE TORQUE TRANSDUCER Hysteresis Dynamometer (HD) Motor Under Test DSP7002 CONNECTED TO HYSTERESIS DYNAMOMETER WITH IN-LINE TORQUE TRANSDUCER © 2018 MAGTROL | Due to continual product development, Magtrol reserves the right to modify specifications without forewarning.

Open the catalog to page 5

DSP 7000 | High-Speed Programmable Controller - 6

DSP7000 SERIES SYSTEM CONFIGURATIONS Hysteresis Dynamometer (HD) Eddy-Current (WB) OR Powder Brake (PB) Dynamometer Motor Under Test Speed Torque DSP7002 CONNECTED TO HYSTERESIS DYNAMOMETER AND EDDY-CURRENT OR POWDER BRAKE DYNAMOMETER Eddy-Current (WB) OR Powder Brake (PB) Dynamometer TM Torque Transducer Speed Torque Excitation DSP7002 Dynamometer Controller PC M-TEST USB DSP7002 CONNECTED TO EDDY-CURRENT OR POWDER BRAKE DYNAMOMETER (WB/PB) WITH IN-LINE TORQUE TRANSDUCER Eddy-Current (WB) OR Powder Brake (PB) Dynamometer Eddy-Current (WB) OR Powder Brake (PB) Dynamometer Torque Excitation...

Open the catalog to page 6

DSP 7000 | High-Speed Programmable Controller - 7

DSP7000 SERIES SYSTEM CONFIGURATIONS Eddy-Current (WB) Dynamometer OR Powder Brake (PB) Dynamometer Powder Brake (PB) Dynamometer Speed Torque Speed Torque DSP7002 CONNECTED TO 2 EDDY-CURRENT OR 2 POWDER BRAKE DYNAMOMETERS (TANDEM SETUP) Powder Brake Dynamometer (PB) Eddy-Current Brake Dynamometer (WB) Transformer Excitation Torque Excitation DSP7002 CONNECTED TO EDDY-CURRENT AND POWDER BRAKE DYNAMOMETER (TANDEM SETUP) The USB Driver required for communication between the PC and DSP7000 is available for download at Magtrol’s website: www.magtrol.com/support/downloads.html © 2018 MAGTROL |...

Open the catalog to page 7