DB-DA/DB-DC | Transducers for measuring radial forces in ball bearings
3Pages

{{requestButtons}}

Catalog excerpts

DB-DA/DB-DC | Transducers for measuring radial forces in ball bearings - 1

DB-DA / DB-DC SERIES DB-DA / DB-DC SERIES TRANSDUCERS FOR MEASURING THE RADIAL LOAD OF BALL BEARINGS FEATURES ▪ Nominal Capacity: - DB-DA: 50, 100, 200, 350 & 750 N - DB-DC: 1 200 N ▪ Built-in Overload Protection up to 10x nominal load - DB-DA: 2x overload nominal load - DB-DC (no mechanical protection) ▪ Combined Error due to Non-Linearity and Hysteresis: < ±0.1 % (DB-DA-50 < ±0.2 %) ▪ Hermetically Sealed; IP 67 Protection Class ▪ 3 Temperature Range available: 0 ... 60 °C, 0 ... 100 °C & 0 ... 160 °C ▪ 3 Bearing Diameter Capabilities: ø17, 20 & 25 mm ▪ Rust-resistant Metallic Construction ▪ Easy to install Cable / Belt Tension Control Magtrol DB-DA and DB-DC transducers are designed for measuring radial forces in ball bearings. Available in several diameters and temperature ranges, these transducers incorporate strain gauge technology and provide a signal output proportional to the force to being measured. APPLICATIONS This transducer is ideally suited for belt, paper or textile tension control and for other measurement of radial forces on rotation cylinders. When connected to a signal conditioner, this transducer is an essential element for highly accurate tension control regulation. Paper / Textile / Foil Tension Control SYSTEM CONFIGURATION PSD PORTABLE SENSOR DISPLAY DATA ENTER DB-DA / DB-DC Load Monitor Signal Conditioner / Display PSD Portable Sensor Display LMU Series Load Monitor Unit © 2021 MAGTROL | Due to continual product development, Magtrol reserves the right to modify specifications without forewarning. Customer Measuring Amplifier

Open the catalog to page 1
DB-DA/DB-DC | Transducers for measuring radial forces in ball bearings - 2

DB-DA / DB-DC SERIES SPECIFICATIONS MODEL TRANSDUCER RATINGS Nominal Load Admissible Overload Overload Limit (without zero drift) a) Maximum Dynamic Load (double amplitude) Minimum Axial Retention Load of Safety Ring with Safety Pin Displacement at Nominal Load ELECTRICAL CHARACTERISTICS Nominal Sensitivity Zero Load Signal Input Impedance Output Impedance Insulation Resistance Supply Voltage Combined Error (nonlinearity + hysteresis) ENVIRONMENT & MECHANICAL CHARACTERISTICS Reference Temperature, nominal Operating Temperature (3 ranges) Temperature Influence on Zero Temperature Influence...

Open the catalog to page 2
DB-DA/DB-DC | Transducers for measuring radial forces in ball bearings - 3

DB-DA / DB-DC SERIES DIMENSIONS 18±0.1 a) Mechanical stopper is not available for DB-DA-XXX-25 (ø25mm) and for DB-DC1200-XX (all diameters) Color mark to quick reconize nominal load RELATED PRODUCTS LMU SERIES - LOAD MONITORING UNIT Magtrol’s Load Monitoring Units are used for measuring load, force and weight from signals generated by strain gauge transducers. Specifically designed for use with Magtrol’s Load LMU 216 Measuring Pins and Load-ForceLoad Monitoring Unit Weight Sensors, the LMU Series provides excitation voltage while conditioning the bridge output signal. Each unit contains...

Open the catalog to page 3

All MAGTROL catalogs and technical brochures

  1. 4 QUADRANT

    2 Pages

  2. ZM Series

    5 Pages

  3. SK-01 Series

    3 Pages

  4. AMF Series

    3 Pages

  5. WB23 & WB27

    7 Pages

  6. Model 5200

    1 Pages

  7. 5211

    1 Pages

  8. 5251-2

    1 Pages

  9. SBB 14

    3 Pages

  10. FMF SERIES

    5 Pages

  11. ZS Series

    7 Pages

  12. RSB

    1 Pages

  13. PC-150

    2 Pages

  14. PCB

    1 Pages

  15. CST 113

    4 Pages

Archived catalogs

  1. WB/PB 65

    8 Pages

  2. WB/PB 15

    8 Pages