Website:
Magnetek
Group: Columbus McKinnon
Catalog excerpts
Electromotive Systems Adjustable Frequency Crane Controls MATERIAL HANDLING ELECTROMOTIVE SYSTEMS
Open the catalog to page 1
ADJUSTABLE FREQUENCY CRANE CONTROLS Magnetek's IMPULSE Drives have long been the gold standard in crane controls for the material handling industry. Advanced safety and performance features combined with our superior application expertise make IMPULSE®»G+ and VG+ Series 3 Crane Controls the best choice to maximize the performance and safety of your material handling system. Standard Features Include: • Load Check™ — reduces possibility of lifting an overload • Load Sharing — allows two or more mechanically coupled motors to be controlled with master/slave torque control •...
Open the catalog to page 2
CONTROL PANELS PRE-ENGINEERED PANELS IMPULSE»G+ Series 3 and IMPULSE»VG+ Series 3 Drives can be purchased as part of a complete, pre-engineered motor control system. These quick-ship, easy-to-install panels offer cost-effective and reliable operation using high quality components. Available in 1 to 30 HP at 230V and 1 to 60 HP at 460V, all panels are tested and quality- approved prior to shipment. Standard Features Include: • 120 Volt control voltage interface card • Brake contactor • Branch fusing • Built-in electronic motor thermal overload protection • Dynamic braking resistor(s) • All...
Open the catalog to page 3
DRIVE SUPPORT TOOLS DRIVE SIMULATION SOFTWARE Simulate an IMPULSE drive right on your computer based PC program that experienced, including: • Programming a drive using a keypad interface • Running the drive using a pendant station • Monitoring input/output status • Programming/executing special functions within the drive such as auto-tuning • Simulating motor loading • Charting/viewing performance characteristics • Simulating alarms/faults • Viewing/editing parameter settings IMPULSE® DRIVE TRENDING TOOL Trend diagnostic feedback from IMPULSE drives program that serves as a digital chart...
Open the catalog to page 4
Brake Test* Encoder Loss Detection* Snapped Shaft Detection* Slack Cable Detection* Roll Back Detection/Torque Proving at Start/Brake Check at Stop* Safe Operating Windows Load Check™ Quick Stop™ Multi-Level Password Protection Phase Loss Detection Control Interface UL/cUL Rated Ground Fault Short Circuit Protection Load Sharing* Hook Height Measurement* Electronic Programmable Limit Switch* Automatic Reset Over-Torque/Under-Torque Detention Slip Compensation Motor Lead Reversal Keypad Copy Static Auto Tune Enhanced Keypad Display Load Float™* Weight Calculation* X-Press Programming™...
Open the catalog to page 5
Adjustable Frequency/Open Loop Vector Controls Class of Service CMAA Class A-F Service Speed Range 40:1 in V/F Mode (15 preset V/F Patterns, 1 Adjustable) 100:1 in Open Loop Vector Mode Speed Control Methods Up to 17 Distinct Speeds (Stepped) Digital Pulse Train Programmable Terminals (8) 1 20 Vac Inputs (3) Digital Dry Contact Relay Outputs (1A Max @ 250 Vac, 1A Max @ 30 Vdc, (1) Dedicated Fault Relay output (1A Max @ 250 Vac, 1A Max @ 30 Vdc, (Consult factory for additional analog/digital input/output option cards) Applications Traverse Motions Worm Gear and Mechanical Load Brake Hoists...
Open the catalog to page 6
Specification Value and Information for all IMPULSE®» G+/VG+ Series 3 Models UL, cUL (CE available upon request) Rated input power supply volts Allowable input voltage fluctuation Allowable input frequency fluctuation Control method Fully digital; sine-wave, V/F control, open loop vector control, flux vector control Maximum output voltage (Vac) 380/400/415/440/460/480V (proportional to input voltage) Rated output frequency (Hz) 0 to 150 Hz (consult factory for applications above 150 Hz) Output frequency accuracy 0.01% — with digital reference command, -10° to 40°C; Frequency reference...
Open the catalog to page 7
MATERIAL HANDLING ELECTROMOTIVE SYSTEMS ENGINEERED SYSTEMS & SOLUTIONS Project Evaluation Project Management Engineering Design System Manufacturing and Testing Field Startup, Testing, Training and Support Customer Training and Maintenance Support Application Solutions PLC/PC Program Development FREQUENCY DRIVES 230, 460 and 575 Volt Power Platforms Exclusive Application Software Specific Crane & Hoist Software OMNIPULSr DIGITAL DRIVES ACCELERATION CONTROL Single & 2 Speed — up to 15.2 Amps Contactor Panels VARIABLE SPEED MOTOR CONTROL PANELS Standard Pre-Engineered Systems Custom...
Open the catalog to page 8All Magnetek catalogs and technical brochures
-
ReFlx® 45 Brochure1 Pages
-
impulse_series_416 Pages
-
FLEX VUE Wireless Controls2 Pages
-
COLLISION AVOIDANCE SYSTEMS2 Pages
-
Cable Reels Brochure2 Pages
-
Magnetek Full Circle Service6 Pages
-
Black Max® Motors4 Pages
-
IMPULSE®•T2 Pages
-
DataLogger Series 41 Pages
-
IMPULSE®•G+ Mini8 Pages
-
IMPULSE®•G+ Series 416 Pages
-
Engineered Systems & Solutions16 Pages
-
Marine Terminal Family8 Pages
-
Brake Accessories Brochure2 Pages
-
Collision Avoidance Brochure2 Pages
-
MH445_SBN2 Pages
-
Enrange? Flex M Receiver2 Pages
-
Enrange? CAN-6 Receiver2 Pages
-
Telemotive MBT2 Pages
-
Telemotive XLTX?2 Pages
-
Telemotive SLTX?2 Pages
-
Telemotive MLTX?2 Pages
-
Telemotive telePendant?2 Pages
-
Telemotive Flex VUE®2 Pages
-
Enrange? Flex EX Series2 Pages
-
OmniPulse? DSD DC Control2 Pages
-
IMPULSE®?R2 Pages
-
MAC??2000 Soft Starts2 Pages
-
IMPULSE®?G+ Mini6 Pages
-
IMPULSE®?G+ Series 416 Pages
-
Telemotive MLTX2?2 Pages
-
Blue Max® Motors6 Pages
-
IMPULSE®?T2 Pages
-
ReFlx® 1202 Pages
-
Braketronic®2 Pages
-
Enrange 300T2 Pages
-
Telemotive telePendant2 Pages
-
Enrange Flex Pro Series2 Pages
-
Enrange Flex EX Series2 Pages
-
Plug & Play Festoon System1 Pages
-
Mill Duty I-Beam Festoon6 Pages
-
Heavy Duty I-Beam Festoon4 Pages
-
C-Track Festoon Systems4 Pages
-
FABA Conductor Rail System2 Pages
-
Electrobar HX Full Brochure2 Pages
-
MAC.20002 Pages
-
Complete Control Panels2 Pages
-
DataLogger Series 3+1 Pages
-
OmniPulse DSD DC Controls2 Pages
-
IMPULSE®?G+ Mini Brochure6 Pages
