MACLIGHT DISPLAY CO., LIMITED Customer No.: Spec Version: Issued Date: Customer approval: ※Please pay more attention for the “inspection standard”, we assume you already agree this standard when place an order with us. ※The specification of “TBD” should refer to the measured value of sample . Maclight Display Co. Ltd www. szmaclight.com Ema

MACLIGHT DISPLAY CO., LIMITED Documents Revision History: Rivision Maclight Display Co. Ltd www. szmaclight.com Email: [email protected]

MACLIGHT DISPLAY CO., LIMITED 1. General Description  The MLT070XH-CT2 model is a Color TFT LCD supplied by Maclight Display Co Ltd.  This main Module has a 7.0 inch diagonally measured active display area with 1024(RGB)X600 resolution. Each pixel is divided into Red, Green and Blue sub-pixels and dots, which are arranged in vertical stripes.  The MLT070XH-CT2 has been designed to apply the HDMI interface method that enables low power, high speed, and high contrast. 2. Mechanical Specification ITEM Standard Value Display Mode Normally White, Transmissive LCD 165.3(W)*121.0(H)*7.95(T) 1024(RGB)X...

MACLIGHT DISPLAY CO., LIMITED *2) T emp.>60℃, Absolute humidity shall be less than 90%RH at 60℃ *3) T emp.≤60℃, 90%RH MAX. *4) The recommended operating conditions refer to a range in which operation of this product is guaranteed. Should this range is exceeded, the operation cannot be guaranteed even if the values may be without the absolute maximum ratings. Accordingly, please make sure that the module is used within this range. And these current values are measured under the condition that all devices are stopped, each component is stable and logic signal is input. Glass cover+glass sensor...

MACLIGHT DISPLAY CO., LIMITED 4. Optical Specification Item Viewing Angle CIE Wy Contrast Ratio Response Time Maclight Display Co. Ltd www. szmaclight.com Email: sal

MACLIGHT DISPLAY CO., LIMITED Electro-optical characteristics test method: Definition of contrast ratio Maclight Display Co. Ltd www. szmaclight.com Email: [email protected]

MACLIGHT DISPLAY CO., LIMITED “White state “:The state is that the LCD should driven by Vwhite. “Black state”: The state is that the LCD should driven by Vblack. Vwhite: T be determined o Vblack: T be determined. o Definition of Response Time: The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from10% to 90%. Definition of color chromaticity (CIE1931) Maclight...

MACLIGHT DISPLAY CO., LIMITED Color coordinates measured at center point of LCD Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Luminance Uniformity(U) = Lmin/ Lmax L-------Active area length W----- Active area width Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Maclight Display Co. Ltd www. szmaclight.com Email: [email protected]

MACLIGHT DISPLAY CO., LIMITED 5. Mechanical Diagram 6 o'clock Viewing Direction Symbol TMDS Data2+ TMDS Data2 Shield TMDS Data2TMDS Data1+ TMDS Data1 Shield TMDS Data1TMDS Data0+ TMDS Data0 Shield TMDS Data0TMDS Clock+ TMDS Clock Shield TMDS ClockCEC Reserved SCL SDA DDC/CEC Ground +5V Power Hot Plug Detect HDMI INTERFACE Symbol VBUS USB DUSB D+ NC GND Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmacli

MACLIGHT DISPLAY CO., LIMITED 6. Interface Pin Connections HDMI interface： Application note: please connected USB interface first, then next connect HDMI interface. Maclight Display Co. Ltd www. szmaclight.com Email: [email protected]

MACLIGHT DISPLAY CO., LIMITED 7. Timing Characteristics 7.1 Horizontal input timing: 7.2 Vertical input timing 8. Inspection Standard A. Sampling Method Unless otherwise agreed upon in writing, the sampling inspection shall be applied to theCustomer’s incoming inspection. 1) Lot size: Quantity per shipment lot 2) Sampling type: Normal inspection , single sampling 3) Inspection level: Ⅱ Maclight Display Co. Ltd www. szmaclight.com Email: [email protected]

MACLIGHT DISPLAY CO., LIMITED 4) 5) Sampling table: MIL-STD-105D Acceptable Quality Level(AQL): Major=0.65Minor=1.5 B. Inspection Method 1) Ambient Condition: a. T emperature: Room temperature 25±5℃ b. Illumination: Single fluorescent lamp non-directive(300 to 700 Lux) 2) Viewing distance The distance between the LCD and the inspector’s eyes shall be at least 30-50cm. 3) Viewing Angle The inspection shall be conducted within normal viewing angle range. Inspection Criteria Inspection Standard Classification defect Display abnormal Short circuit Missing segment Excess power consumption No backligt,...

MACLIGHT DISPLAY CO., LIMITED For dot defect of TFT LCD which is not smaller than 3 inches, dividing three areas to make a judgment (according to figure 1). A area : center of viewing area B area : periphery of viewing area Viewing Area A zone: Viewing Area(VA) C area : Outside viewing area For other defects, dividing two areas to make a judgment (according figure 2). A zone : Inside Viewing area B zone : Outside Viewing area X1(A.A~V.A): 2mm B. Cosmetic defect criteria Judgment standard Inspection items Acceptable number Black spot, White spot, Bright Spot, Pinhole, Foreign a Particle, Particle...

MACLIGHT DISPLAY CO., LIMITED A Total defective point(B,C) TFT LCD is smaller than 3 inches Bright dot Dark dot Total Bright dot Dark dot Total Defect Dark dot Total Bright dot Dark dot Total Notes: Bright dot: in R、G、B or dark display figure, the pixel appears bright. Dark dot: in R、G、B or white display figure, the pixel appears dark. Defect area must be less than an half size of the dot. 5 Bubble inside cell Polarizer defect (if Polarizer is used) any size Scratch ,damage on polarizer, Particle on polarizer or between polarizer and glass. Bubble, dent and convex Refer to item 1 and item 2....