MLT013G24-1
17Pages

MACLIGHT DISPLAY CO., LIMITED Customer No.: Spec Version: Issued Date: Customer approval: ※Please pay more attention for the “inspection standard”, we assume you already agree this standard when place an order with us. ※The specification of “TBD” should refer to the measured value of sample . Maclight Display Co. Ltd www. szmaclight.com Ema

MACLIGHT DISPLAY CO., LIMITED Documents Revision History: Rivision Change interface Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 1. General Description The MLT013G24-1 model is a Color TFT LCD supplied by Maclight Display Co Ltd.  This main Module has a 1.30 inch diagonally measured active display area with 240(RGB)X240 resolution. Each pixel is divided into Red, Green and Blue sub-pixels and dots, which are arranged in vertical stripes.  The MLT013G24-1 has been designed to enables high brightness, high speed, and high contrast.  2. Mechanical Specification ITEM Standard Value Display Mode Module Dimension Resolution Active Display Area Dot Size Input Data Viewing Direction LED...

MACLIGHT DISPLAY CO., LIMITED Storage temperature  Backlight Characteristics Item Forward Voltage Forward current Chroma Uniformity Optical Specification Response time Contrast ratio Maclight Display Co. Ltd www. szmaclight.com Email: sales@sz

MACLIGHT DISPLAY CO., LIMITED Color chromaticity Luminance Lumin ance Electro-optical characteristics test method: Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED Definition of contrast ratio “White state “:The state is that the LCD should driven by Vwhite. “Black state”: The state is that the LCD should driven by Vblack. Vwhite: T be determined o Vblack: T be determined. o Definition of Response Time: The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from10% to 90%. Maclight Display Co....

MACLIGHT DISPLAY CO., LIMITED Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Luminance Uniformity(U) = Lmin/ Lmax L-------Active area length W----- Active area width Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 5. Mechanical Diagram Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 6. Interface Pin Connections Pin No. Power supply for backlight cathode input terminal. Power supply for backlight cathode input terminal. Tearing effect signal is used to synchronize MCU to frame memory Serial input/output data 1 Serial input data 2 Serial clock signal Chip selection signal Power supply for interface pins. (1.8V) Power supply for interface pins. (1.8V) Power supply for liquid crystal power supply analog circuit. Power supply for liquid crystal power supply analog circuit. Power supply for backlight anode input terminal. Power supply for...

MACLIGHT DISPLAY CO., LIMITED 7. Inspection Criterion A. Sampling Method Unless otherwise agreed upon in writing, the sampling inspection shall be applied to theCustomer’s incoming inspection. 1) Lot size: Quantity per shipment lot 2) Sampling type: Normal inspection , single sampling 3) Inspection level: Ⅱ 4) Sampling table: MIL-STD-105D 5) Acceptable Quality Level(AQL): Major=0.65Minor=1.5 B. Inspection Method 1) Ambient Condition: a. T emperature: Room temperature 25±5℃ b. Illumination: Single fluorescent lamp non-directive(300 to 700 Lux) 2) Viewing distance The distance between the LCD...

MACLIGHT DISPLAY CO., LIMITED 8. Inspection Criteria Inspection Standard Classification defect Display abnormal Short circuit Missing segment Excess power consumption No backligt, flickering 2 Missing compement Outline Dimension out of drawing tolerance 2) Cosmetic defect A. Definition of inspection range For dot defect of TFT LCD which is not smaller than 3 inches, dividing three areas to make a judgment (according to figure 1). A area : center of viewing area B area : periphery of viewing area C area : Outside viewing area Viewing Area A zone: Viewing Area(VA) For other defects, dividing...

MACLIGHT DISPLAY CO., LIMITED B. Cosmetic defect criteria Judgment standard Inspection items Pinhole, Foreign Particle, Particle in or on glass, Scratch on glass Black spot, White spot, Bright Spot, 1 Acceptable number 3 Total defective point(B,C) Black line, White line, and Particle Between 2 Polarizer and glass, Scratch on glass

MACLIGHT DISPLAY CO., LIMITED Notes: Bright dot: in R、G、B or dark display figure, the pixel appears bright. Dark dot: in R、G、B or white display figure, the pixel appears dark. Defect area must be less than an half size of the dot. 5 Bubble inside cell Polarizer defect (if Polarizer is used) any size Scratch ,damage on polarizer, Particle on polarizer or between polarizer and glass. Bubble, dent and convex Refer to item 1 and item 2. Stage surplus glass b b≦0.3mm Surplus 7 Surrounding surplus glass Should not influence outline dimension and assembling. Contrast ratio uneven According to the...

MACLIGHT DISPLAY CO., LIMITED ②Surrounding crack―non-contact side b < Inner borderline of the seal Inner border line of the seal Outer border line of the seal ③ Surrounding crack― contact side seal t b < Outer borderline of the seal Inner border line of the seal Outer border line of the seal a ≦ t, b ≦ 3.0, c ≦ 3.0 Glass crack should not cover patterns u and alignment mark and patterns. Inspection items Judgment standard Category(application: B zone) Component Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmacl