MLT013G12-1
15Pages

MACLIGHT DISPLAY CO., LIMITED Customer No.: Spec Version: Issued Date: Customer approval: ※Please pay more attention for the “inspection standard”, we assume you already agree this standard when place an order with us. ※The specification of “TBD” should refer to the me

MACLIGHT DISPLAY CO., LIMITED Documents Revision History: Rivision

MACLIGHT DISPLAY CO., LIMITED 1. General Specifications MLT013G12-1 V2 is a TFT-LCD module. It is composed of a TFT-LCD panel, driver IC, FPC, a back light unit. The 1.3 display area contains 240 x 240 pixels and can display up to 65K/262K colors. This product accords with RoHS environmental criterion. Display color Viewing Direction Operating temperature Storage temperature Module size Active Area(W×H) Outline Dimensions Refer to outline drawing

MACLIGHT DISPLAY CO., LIMITED 2. Outline Drawing 焊锡处高度 黄色绝缘胶纸

MACLIGHT DISPLAY CO., LIMITED 3. Absolute Maximum Ratings(Ta=25℃) 3.1 Electrical Absolute Maximum Ratings.(Vss=0V ,Ta=25℃) Item Analog Supply Voltage Logic Input Voltage 3.2 Environmental Absolute Maximum Ratings. Ambient Temperature 1. The response time will become lower when operated at low temperature. 2. Background color changes slightly depending on ambient temperature. The phenomenon is reversible. 3. Ta<=40℃:85%RH MAX. Ta>=40℃:Absolute humidity must be lower than the humidity of 85%

MACLIGHT DISPLAY CO., LIMITED 4. Electrical Specifications and Instruction Code 4.1 Electrical characteristics(Vss=0V ,Ta=25℃) Parameter System Voltage Interface Operation Voltage Operating Current for VDD Sleep_In Mode VDDIO Gate Driver Voltage Note: 1: Tested in 1╳1 chessboard pa

MACLIGHT DISPLAY CO., LIMITED 4.2 LED backlight specification

MACLIGHT DISPLAY CO., LIMITED 4.3 Interface signals Description Power Ground LED Cathode LED Anode Power Supply for Analog Power Ground Power Ground Display data/command selection pin in 4-line serial interface. Chip selection pin;Low enable,high disable. This pin is used to be serial interface clock SPI interface input/output pin.the data is latched on the rising edge of the SCL signal. This signal will reset the device and it must be applied to properly initialize the chip.Signal is active low. Power Ground

MACLIGHT DISPLAY CO., LIMITED 5. Optical Characteristics Item Viewing Angle Contrast Ratio Response Time Note：The parameter is slightly changed by temperature, driving voltage and materiel Note 1: The data are measured after LEDs are turned on for 5 minutes. LCM displays full white. The brightness is the average value of 9 measured spots. Measurement equipment PR-705 (Φ8mm) Measuring condition: - Measuring surroundings: Dark room. - Measuring temperature: Ta=25℃. - Adjust operating voltage to get optimum contrast at the center of the display. Measured value at the center point of LCD panel...

MACLIGHT DISPLAY CO., LIMITED Note 2: The luminance uniformity is calculated by using following formula. ⊿Bp = Bp (Min.) / Bp (Max.)×100 (%) Bp (Max.) = Maximum brightness in 9 measured spots Bp (Min.) = Minimum brightness in 9 measured spots. Active area Note 3: The definition of viewing angle: Refer to the graph below marked by θ and Ф

MACLIGHT DISPLAY CO., LIMITED Note 4: Definition of contrast ratio.( Test LCD using DMS501) Brightness of selected dots Brightness of non  selected dots Note 5: Definition of Response time. (Test LCD using DMS501): The output signals of photo detector are measured when the input signals are changed from “black” to “white”(falling time) and from “white” to “black”(rising time), respectively. The response time is defined as the time interval between the 10% and 90% of amplitudes.Refer to

MACLIGHT DISPLAY CO., LIMITED The definition of response time Note 6: Definition of Color of CIE Coordinate and NTSC Ratio. Color gamut: area of RGB triangle  100% area of NTSC triangle Note 7: Definition of cross talk. Cross talk ratio(%)=|pattern A Brightness-pattern B Brightness|/pattern A Brightness*100 Measurement point(center) Electric volume value=3F+/-3Hex

MACLIGHT DISPLAY CO., LIMITED 6. Reliability Test Items and Criteria No Test Item Test condition High Temperature Storage High Temperature Operation High Temperature/Humidity Operation 1. After testing, cosmetic and electrical defects should not happen. 2. Total current consumption should not be more than twice of initial value. Temperature Cycle after 5 cycle, Restore 2H at 25℃ Power off Note: Operation: Supply 2.8V for logic system. The inspection terms after reliability test, as below ITEM

MACLIGHT DISPLAY CO., LIMITED 7. Precautions for Use of LCD Modules 7.1 Handling Precautions 7.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 7.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 7.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 7.1.4 The polarizer...

MACLIGHT DISPLAY CO., LIMITED d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 7.2 Storage precautions 7.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 7.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : Relatively humidity: 7.2.3 The LCD modules should be stored in the room without acid, alkali and harmful...