MLT011G13-1
16Pages

MACLIGHT DISPLAY CO., LIMITED Customer No.: Spec Version: Issued Date: Customer approval: ※Please pay more attention for the “inspection standard”, we assume you already agree this standard when place an order with us. ※The specification of “TBD” should refer to the measured value of sample . Maclight Display Co. Ltd www. szmaclight.com Ema

MACLIGHT DISPLAY CO., LIMITED Documents Revision History: Rivision Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 1. General Specifications MLT011G13-1 is a TFT-LCD module. It is composed of a TFT-LCD panel, driver IC, FPC, a back light unit . The 1.14 display area contains 135 x (RGB)x 240 pixels and can display up to 65K colors. This product accords with ROHS environmental Criterion. Item Display color Viewing Direction Operating temperature Storage temperature Module size Active Area(W×H) Color tune is slightly changed by temperature and driving voltage. Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclig

MACLIGHT DISPLAY CO., LIMITED 2. Outline Drawing Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 3. Absolute Maximum Ratings 3.1 Electrical Absolute Maximum Ratings. Analog Supply Voltage Logic Input Voltage 3.2 Environmental Absolute Maximum Ratings. Ambient Temperature Notes: 1. The response time will become lower when operated at low temperature. 2. Background color changes slightly depending on ambient temperature. The phenomenon is reversible. 3. Ta<=40℃:85%RH MAX. Ta>=40℃:Absolute humidity must be lower than the humidity of 85%RH at 40℃. Maclight Display Co. Ltd www. szmaclight.com Email: sales@szma

MACLIGHT DISPLAY CO., LIMITED 4. Electrical Specifications 4.1 Operating Conditions Parameter System Voltage Gate Driver High Voltage Gate Driver Low Voltage Sleep_In Mode VDDIO Power Consumption Life Time Note: 1. Where ILED =20mA , VLED=3.0V , Pbl= ILED x VLED 2. Uniform measure condition: a:Measure 9 point ,Measure location is show below: b:Uniform=(Min brightness/Max brightness)x100% c:Best Contrast. Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 3. The environmental conducted under ambient air flow ,at Ta=25±2oC,60%RH±5% Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 4.3 Interface signals This pin is used to be serial interface clock. Display data/command selection pin in 4-line serial interface. Power Supply for Analog Power Ground. This signal will reset the device ,Signal is active low. Chip selection pin ,Low enable ,High disable. Power Ground. No Connect. Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 4.4 AC Characteristics 4.4.1 Serial interface Characteristics(4-line serial): Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 5. Optical Characteristics Item Viewing Angle Contrast Ratio Response Time NTSC Ratio Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclig

MACLIGHT DISPLAY CO., LIMITED Note：The parameter is slightly changed by temperature, driving voltage and materiel Note 1: The data are measured after LEDs are turned on for 5 minutes. LCM displays full white. The brightness is the average value of 9 measured spots. Measurement equipment BM-7 (Φ5mm) Measuring condition: - Measuring surroundings: Dark room. - Adjust operating voltage to get optimum contrast at the center of the display. Measured value at the center point of LCD panel after more than 5 minutes while backlight turning on. Note 2: The luminance uniformity is calculated by using...

MACLIGHT DISPLAY CO., LIMITED Note 3: The definition of viewing angle: Refer to the graph below marked by θ and Ф Note 4: Definition of contrast ratio.( Test LCD using DMS501) Brightness of selected dots Brightness of non  selected dots Note 5: Definition of Response time. (Test LCD using DMS501): TThe output signals of photo detector are measured when the input signals are changed from“black”to“white”(falling time) and from“ white”to “black”(rising time), respectively. The response time is defined as the time interval between the 10% and 90% of amplitudes.Refer to figure as below. The...

MACLIGHT DISPLAY CO., LIMITED Note 6: Definition of Color of CIE Coordinate and NTSC Ratio. Color gamut: area of RGB triangle  100% area of NTSC triangle Note 7: Definition of cross talk. Cross talk ratio(%)=|pattern A Brightness-pattern B Brightness|/pattern A Brightness*100 Measurement point(center) Electric volume value=3F+/-3Hex Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 6. Reliability Test Items and Criteria Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 7. Precautions for Use of LCD Modules 7.1 Handling Precautions 7.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 7.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 7.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 7.1.4 The polarizer...

MACLIGHT DISPLAY CO., LIMITED 7.2 Storage precautions 7.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 7.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : Relatively humidity: 7.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 7.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine....