MLT009G8-01
21Pages

MACLIGHT DISPLAY CO., LIMITED Customer No.: Spec Version: Issued Date: Customer approval: ※Please pay more attention for the “inspection standard”, we assume you already agree this standard when place an order with us. ※The specification of “TBD” should refer to the measured value of sample . Maclight Display Co. Ltd www. szmaclight.com Ema

MACLIGHT DISPLAY CO., LIMITED Documents Revision History: Rivision Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 1. General Description  The MLT009G8-01 model is a Color TFT LCD supplied by Maclight Display Co Ltd.  This main Module has a 0.96 inch diagonally measured active display area with 80(RGB)X160 resolution. Each pixel is divided into Red, Green and Blue sub-pixels and dots, which are arranged in vertical stripes.  The MLT009G13-06 has been designed to apply the parallel interface method that enables low power, high speed, and high contrast. 2. Mechanical Specification ITEM Standard Value Display Size 0.96 inch(Diagonal) Normally black, Transmissive LCD...

MACLIGHT DISPLAY CO., LIMITED *2) T emp.>60℃, Absolute humidity shall be less than 90%RH at 60℃ *3) T emp.≤60℃, 90%RH MAX. *4) The recommended operating conditions refer to a range in which operation of this product is guaranteed. Should this range is exceeded, the operation cannot be guaranteed even if the values may be without the absolute maximum ratings. Accordingly, please make sure that the module is used within this range. And these current values are measured under the condition that all devices are stopped, each component is stable and logic signal is input. Model Characteristics...

MACLIGHT DISPLAY CO., LIMITED 4. Optical Specification Item Viewing Angle CIE Wy Contrast Ratio Response Time Maclight Display Co. Ltd www. szmaclight.com Email: sal

MACLIGHT DISPLAY CO., LIMITED Electro-optical characteristics test method: Definition of contrast ratio Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED “White state “:The state is that the LCD should driven by Vwhite. “Black state”: The state is that the LCD should driven by Vblack. Vwhite: T be determined o Vblack: T be determined. o Definition of Response Time: The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (TON) is the time between photo detector output intensity changed from 90% to 10%. And fall time (TOFF) is the time between photo detector output intensity changed from10% to 90%. Definition of color chromaticity (CIE1931) Color...

MACLIGHT DISPLAY CO., LIMITED Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer Fig. 2). Every measuring point is placed at the center of each measuring area. Luminance Uniformity(U) = Lmin/ Lmax L-------Active area length W----- Active area width Lmax: The measured maximum luminance of all measurement position. Lmin: The measured minimum luminance of all measurement position. Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 5. Mechanical Diagram Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 6. Interface Pin Connections FPC Connector is used for the module electronics interface. Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 7. Timing Characteristics 7.1 Serial Interface Characteristics (4-line Serial) Note : The rising time and falling time (Tr, Tf) of input signal are specified at 15 ns or less. Logic high and low levels are specified as 30% and 70% of VDDI for Input signals. Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 7.2 Reset timing: Maclight Display Co. Ltd www. szmaclight.com Email: sales@szmaclight.com

MACLIGHT DISPLAY CO., LIMITED 8. Inspection Standard A. Sampling Method Unless otherwise agreed upon in writing, the sampling inspection shall be applied to theCustomer’s incoming inspection. 1) Lot size: Quantity per shipment lot 2) Sampling type: Normal inspection , single sampling 3) Inspection level: Ⅱ 4) Sampling table: MIL-STD-105D 5) Acceptable Quality Level(AQL): Major=0.65Minor=1.5 B. Inspection Method 1) Ambient Condition: a. T emperature: Room temperature 25±5℃ b. Illumination: Single fluorescent lamp non-directive(300 to 700 Lux) 2) Viewing distance The distance between the LCD...

MACLIGHT DISPLAY CO., LIMITED 9. Inspection Criteria Inspection Standard Display abnormal defect Major Short circuit Missing segment Excess power consumption No backligt, flickering 2 Missing compement Outline Dimension out of drawing tolerance 2) Cosmetic defect A. Definition of inspection range For dot defect of TFT LCD which is not smaller than 3 inches, dividing three areas to make a judgment (according to figure 1). A area : center of viewing area B area : periphery of viewing area Viewing Area A zone: Viewing Area(VA) C area : Outside viewing area For other defects, dividing two areas...

MACLIGHT DISPLAY CO., LIMITED B. Cosmetic defect criteria Judgment standard Inspection items Pinhole, Foreign Particle, Particle in or on glass, Scratch on glass Black spot, White spot, Bright Spot, 1 Acceptable number 3 Total defective point(B,C) Black line, White line, and Particle Between 2 Polarizer and glass, Scratch on glass

MACLIGHT DISPLAY CO., LIMITED Total Notes: Bright dot: in R、G、B or dark display figure, the pixel appears bright. Dark dot: in R、G、B or white display figure, the pixel appears dark. Defect area must be less than an half size of the dot. 5 Bubble inside cell Polarizer defect (if Polarizer is used) any size Scratch ,damage on polarizer, Particle on polarizer or between polarizer and glass. Bubble, dent and convex Refer to item 1 and item 2. Stage surplus glass b Surrounding surplus glass Should not influence outline dimension and assembling. Contrast ratio uneven According to the limit...