E3-HEAVY DUTY
53Pages

HEAVY DUTY MOTORS

HEAVY DUTY HYDRAULIC MOTORS CONTENTS Page “M+S HYDRAULIC” can accept no responsibility for possible errors in catalogues, brochures and other printed material. “M+S HYDRAULIC” reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.

DISC VALVE HYDRAULIC MOTORS GENERAL INFORMATION: Orbit motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Hydraulic orbit motors operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits the torque generated by the application of pressure from hydraulic oil fed into motor which is then delivered via the motor's output shaft. Orbit motors have high starting torque and constant output torque at wide speed range. The output shaft runs on tapered roller bearings and can absorb high...

HYDRAULIC MOTORS MSWM APPLICATION » » » » » » » » Sawmill machines Woodworking machines Metal working machines Agriculture machines Road building machines Mining machinery Food industries Special vehicles etc. » Model- Disc valve, roll-gerotor » Wheel mount » Side and rear ports » Shafts- straight, splined and tapered » Metric and BSPP ports » Other special features Max. Pressure Drop, Max. Oil Flow, Mineral based- HLP(DIN 51524) or HM(ISO 6743/4) Temperature range, Optimal Viscosity range, mm /s [SUS] ISO code 20/16 (Min. recommended fluid filtration of 25 micron) Oil flow in Pressure drop...

MSWM EPMS MOTORS MOTORS SPECIFICATION DATA daNm [lb-in] with Drain Line Max. Starting Pressure with Unloaded Shaft, bar [PSI] Min. Starting Torque daNm [lb-in] Min. Speed***, [RPM] * Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code 20/16. A nominal f iltration of 25 micron...

MSWM EPMS MOTORS MOTORS DIMENSIONS AND MOUNTING DATA max 128 [5.039] C: 2xM10-12 mm [.47 in] depth P(A,B): 2xG1/2 or 2xM22x1,5-15 mm [.59 in] depth T: G ¼ or M14x1,5- 12 mm [.47 in] depth (plugged) Type Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW PERMISSIBLE SHAFT LOADS The output shaft runs in tapered bearings that permit high axial and radial forces. Curve "1" shows max. radial shaft load at bearing life of 2000 hours at 100 RPM. Curve "2" shows max. radial...

MSWM EPMS MOTORS MOTORS SHAFT EXTENSIONS C -ø40 straight, Parallel key A12x8x70 DIN 6885 Max. Torque 132,8 daNm [11755 ln-in] Max. Torque 210,7 daNm [18650 lb-in] Max. Torque 132,8 daNm [11755 ln-in] S=46 Tightening torque 50±3 daNm [4425±265 lb-in] M -ø1½" splined 17T, DP 12/24 ANSI B92.1-1976 Max. Torque 132,8 daNm [11755 ln-in] MSWM Pos.1 - Port type omit - Side ports E - Rear ports Pos. 5 - Special Features (see page 48) Pos. 6 - Design Series omit - Factory specified NOTES: * The permissible output torque for shafts must not be exceeded! The hydraulic motors are mangano-phosphatized as...

HYDRAULIC MOTORS MTK APPLICATION » Conveyors » Metal working machines » Machines for agriculture » Road building machines » Mining machinery » Food industries » Special vehicles » Plastic and rubber machinery etc. » Model- Disc valve, roll-gerotor » Flange mount with wheel mount » Side and rear ports » Shafts- straight, splined and tapered » Metric, SAE and BSPP ports » Other special features daNm [lb-in] Permissible Shaft Loads, Pa=1000 [2250] Mineral based- HLP(DIN 51524) or HM(ISO 6743/4) Temperature range, Optimal Viscosity range, mm /s [SUS] ISO code 20/16 (Min. recommended fluid...

MTK EPMS MOTORS MOTORS daNm [lb-in] Max. Starting Pressure with Unloaded Shaft, bar [PSI] at max. pressure Min. Starting Torque, drop cont. daNm [lb-in] Max. Return Pressure without Drain Line, with Drain Line, Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds of 5 RPM lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code 20/16....

MTK EPMS MOTORS MOTORS DIMENSIONS - MTK W and MTK C R Shaft CO Shaft SB Shaft R Shaft CO Shaft SB Shaft Rear Ports Dim. See Page 12 Versions Rear Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

MTK EPMS MOTORS MOTORS Rear Ports Dim. See Page 12 Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW Type MTKF 160 MTKF 200 MTKF 250 MTKF 315 MTKF 400 MTKF 470 MTKF 500

MTK EPMS MOTORS MOTORS Rear Ports

MTK EPMS MOTORS MOTORS W 4-Bolt flange, Wheel Motor spigot diameter 107,9 mm [2.25 in] - BC 147,6 mm [5.81 in] L5 C 4-Bolt flange, spigot diameter 127 mm [4.99 in] - BC 161,92 mm [6.375 in] Type MTKC...CO... MTKC...SB... MTKC...R... MTKC...K... MTKC...T... F 6-Bolt flange, spigot diameter 82,5 mm [3.25 in] - BC 106,35 mm [4.19 in] L5 15,5 [.61] Type MTKF...CO... MTKF...SB... MTKF...R... MTKF...K... MTKF...T...

MTK EPMS MOTORS MOTORS SHAFT EXTENSIONS ø1.25” [31,75] srtaight, Parallel key 16 "x 16 "x 1 ¼" Max. Torque 77 daNm [6815 lb-in] 5 Max. Torque 20±1 daNm [1770±88.5 lb-in] Max. Torque 20±1 daNm [1770±88.5 lb-in] T ø1.625” [41,275] tapered 1:8, Parallel key 16 "x Max. Torque 100 daNm [8850 lb-in]