Rack & pinion units - LZG 20
6Pages

{{requestButtons}}

Catalog excerpts

Rack & pinion units - LZG 20 - 1

RACK & PINION UNITS LZG 20 // Rack & pinion units 5500 –10000 N > Extremely robust top-quality universal rack & pinion units with a very compact design. When mounted to support, cause absolutely minimal shading because input shaft is below the gutter. > Universal application for spacing of push-pull tube above beam of 40, 60 or 60/200 mm as well as C-section 11.5 mm. > The support version is easy to install by clamping to the support – support dimensions 80, 100, 120 or 140 mm x 50, 60 or 80 mm are possible. Please indicate support dimensions on order! Support mounting > Stable cast housing with ball bearings for quiet operation. Gear components of high-tempered steel, 10000 N version with additional hardening. > Hex shaft for ease of assembly of prefab tubes, low levels of torsion and clearance. Robust input shaft for the transmission of high torque levels. Securing on the beam with two bolts (by customer) with strength 8.8. > Rack made of milled steel (25 x 35 mm / 30 x 40 mm) with integrated connection for 27/32 mm push-pull tube. > Standard colour DB 701 (platinum grey). > The rack is delivered pre-greased. Including tensioning pin Rail mounting Support mounting module Gear unit Rail mounting module LOCK BEWEGT // LOCK MOVES

Open the catalog to page 1
Rack & pinion units - LZG 20 - 2

RACK & PINION UNITS 19 LZG 20 > Support mounting LZG 20.10 / 20.30 Support mounting C-section 60 mm, 40 mm LZG 20 // Gear unit Support mounting 0 LOCK BEWEGT // LOCK MOVES

Open the catalog to page 2
Rack & pinion units - LZG 20 - 3

20 RACK & PINION UNITS Retaining screws > Select support mounting rack on p. 22 LZG 20 > Gable mounting LZG 20.60 Gable mounting // C-section 11.5 mm LZG 20 // Gear unitGable mounting > Select rack for complete gable mounting on p. 22 o LOCK BEWEGT // LOCK MOVES

Open the catalog to page 3
Rack & pinion units - LZG 20 - 4

RACK & PINION UNITS 21 LZG 20 > rail mounting LZG 20.20 // LZG 20.40 Rail mounting // 60 mm, LZG 20 // Gear unitrail mounting > Select rack for complete rail mounting on p. 22 0 LOCK BEWEGT // LOCK MOVES

Open the catalog to page 4
Rack & pinion units - LZG 20 - 5

22 RACK & PINION UNITS > Determining the optimum length of rack, see p. 23 LZG 20 rack heads 0 23,3 mm // 0 28,3 mm 1 bore horizontal o LOCK BEWEGT // LOCK MOVES

Open the catalog to page 5
Rack & pinion units - LZG 20 - 6

RACK & PINION UNITS 23 Determining length of rack on LZG 20 / LZG 24 rail ventilation Support mounting: nimuuuuuiiuu > Selection procedure and sample calculation: Use this procedure to determine the input values for the calculation formula. Use own values Use own values Rack installation space: 1 120 > With rail mounting, installation space CE = 0 Gear unit width GL [mm] = 114 > Calculation formula and sample calculation: Use this formula to calculate the required rack length, then select a rack that is just slightly longer than and closest to that dimension. You can also reduce...

Open the catalog to page 6

All Lock Antriebstechnik GmbH catalogs and technical brochures