LF-ADD040-1050-42
10Pages

LF-ADD040-1050-42 DALI Dimmable LED Driver DALI or PUSH dimmable Current adjustable via DIP switch 1% dimming depth; standby power consumption <0.5W Supports corridor function (corridor DIM) and emergency escape lighting system Suitable for Class II light fixtures 5-year warranty (please refer to the warranty condition) Applications · Indoor office lighting · commercial lighting · residential lighting Descriptions LF-ADD040-1050-42 is a 40W DALI or PUSH dimmable constant current LED driver supporting corridor function (corridor DIM) and emergency escape lighting system via Lifud programmer. Its input voltage ranges from 220 to 240Vac and output current is adjustable via DIP switch from 700 to 1050mA with every 50mA as a step. It has all-round protections: over voltage protection and short circuit protection. ADD: DALI dimmable LED driver Lifud Technology Co., Ltd. Production Base I (HQ): Building B, Kutto Industrial Park, NO.26 Xinhe Road, Bao'an District, Shenzhen, China. Production Base II: No.4, Block 2, Tengfei Road, Shigao Economic Development Zone, Tianfu New Area, Sichuan, China. Website: www.lifud.com Telephone: +86(0)755 8373 9299 Email

LF-ADD040-1050-42 DALI Dimmable LED Driver n Electrical Characteristics Model Output Voltage Output Current Input Frequency Input Current Inrush Current Load Quantities of Circuit Breaker Leakage Current Standby Power Consumption Environment Descriptions Start-up Time Protection Characteristics Flicker Index IEC-Pst ≤1, CIE SVM ≤0.4 (Modulation Depth) Complies with IEEE Std 1789-2015 Temperature Drift <0.7mA ≤0.5W (when PWM OFF signal is effective) Open Circuit Short Circuit Hiccup mode (auto-recovery) Operating Temperature Operating Humidity 20-95%RH (no condensation) Storage Temperature/...

LF-ADD040-1050-42 DALI Dimmable LED Driver n Electrical Characteristics Certifications Withstand Voltage Insulation Resistance Safety & EMC Safety Standards IP Rating RoHS Other Parameters DALI Standard Noise Level Warranty IP20 RoHS 2.0 (EU) 2015/863 IEC62386-101 102 207: DALI2.0 ≤29dB (this data is measured in a soundproof room and the noise collector should be 10CM away from LED driver) 5 years (Tc≤80℃) Test Equipment AC power source: CHROMA6530, digital power meter: CHROMA66202, oscilloscope: Tektronix DPO3014, DC electronic load: M9712B, LED board, constant temperature and humidity...

LF-ADD040-1050-42 DALI Dimmable LED Driver Additional Remarks 1. It is recommended that user install the over voltage protection, under voltage protection and surge protection devices in the power supply circuits of light fixtures to ensure electricity safety. 2. The LED driver used in combination with the end device is one of the accessories of the whole light fixture, and the EMC of the whole light fixture is not only susceptible to the driver itself, but to the LED light fixture and the whole light fixture's wiring. Thus, the manufacturer of LED light fixture should re-confirm the EMC of...

LF-ADD040-1050-42 DALI Dimmable LED Driver n Product Definitions Product Terminals INPUT Positive electrode output of LED driver Negative electrode output of LED driver Input terminal of AC live wire Input terminal of AC neutral wire Remark: when adjusting the output current via the DIP switch, please disconnect input AC first so as to use the DIP switch without the input AC connected. Wiring Diagram of PUSH Dimming PUSH Switch PUSH Dimming Operations • Connect the PUSH switch in series between AC-L and DA1 PUSH terminals; connect AC-N to DA2 PUSH terminal. Do not directly connect AC-L and...

LF-ADD040-1050-42 DALI Dimmable LED Driver n Dimming Operation Instructions PUSH Dimming Operations Operation Instant Push Long Push Reset Push The PUSH operation won’t cause any variations on LED driver if it’s less than 0.1S. Min. dimming depth of PUSH dimming: 1% (Iout) The PUSH dimming mode has the memory function in case of any power failure. When the LED driver is powered on again, the light will return to the previous state before power failure. The present PUSH dimming direction is opposite to the fomer one. Max. wire length from the PUSH switch to the farthest LED driver: 135m;...

LF-ADD040-1050-42 DALI Dimmable LED Driver n Dimming Operation Instructions Wiring Diagram of Corridor Dimming (sensor switch) Sensor Output DA2 PUSH AC-L (mains-live wire) Sensor Input Driver Connector Operations for Entering Corridor Lighting Mode Approach 1: keep moving in the effective sensing area for 3+ mins (set the sensor’s hold time for 3+ mins) to enable the corridor dimming mode; Approach 2: replace the sensor with an ordinary switch and keep it on for 3+ mins so as to switch to the corridor dimming mode (automatically); Approach 3: use Lifud programmer to enable the driver’s...

LF-ADD040-1050-42 DALI Dimmable LED Driver n Dimming Operation Instructions Working Process of Corridor Dimming Mode Brightness Sensing Brightness Unattended Brightness Sensor Signal Default Value Available Setting Scope Fade-in time of sensing Hold time of sensing Wait time of sensing Fade-out time of sensing Unattended time Sensing brightness Unattended brightness Operations for Emergency Escape Lighting System When there is no mains input, the driver switches to the emergency escape lighting system; driver’s output: 15% (Iomax) Emergency input voltage: 180-264Vdc Remarks: 1. The...

LF-ADD040-1050-42 DALI Dimmable LED Driver n Structure & Dimensions (unit: mm) Product Dimensions Model Center-to-center Spacing of Positioning Hole Diameter of Positioning Hole Structure Diagram n Packaging Specifications Model Carton Size 10 pcs/layer; 7 layers/ctn; 70 pcs/ctn Lifud Technology Co., Ltd. Production Base I (HQ): Building B, Kutto Industrial Park, NO.26 Xinhe Road, Bao'an District, Shenzhen, China. Production Base II: No.4, Block 2, Tengfei Road, Shigao Economic Development Zone, Tianfu New Area, Sichuan, China. Website: www.lifud.com Telephone: +86(0)755 8373 9299 Email:...