5 Axis Workholding Systems Machining on 5 sides with one single clamping operation

VB 5AX100 5 AXIS WORKHOLDING SYSTEM VB 5 AX 100 S CHENKE C LAMPING S YSTEM – M ODELS VB 5AX100-H VB 5AX100-H The rational vise system for 5 axis machining • High clamping force (up to 40 kN) exactly where it is needed, by incorporating the tension spindle directly below the work piece support. • Form fit clamping with embossing pins. No pre-embossing required. • No flare out of the jaws under tension, no distortion on machine table. Clamping Height above machine table (CH) • Extreme rigidity permits maximum cutting forces. Extended height +25 mm see pos.17 (Parts No. 740-04-025-00) Extended height...

VB 5AX100 5 AXIS WORKHOLDING SYSTEM VB 5AX100-H Basic Standard Set (Vise-Set and mounting blocks) Designation Tension spindle with driving sleeve and spindle nut Extension shaft with cap nut Support blades optional Order seperately, according to required clamping height above table (CH) (100, 125 ,150, 175, 200, 225 mm) Parts No. 740-12-xxx-xx H Mounting blocks (at user’s choice) Depending on the machine table or fixture Order seperately Parts No. 740-02-xxx-xx Parts No. 740-03-xxx-xx Parts No. 740-05-xxx-xx Parts No. 740-06-xxx-xx CH = Clamping Height Above Table OH = Overall height Order screws/brackets...

VB 5AX100 5 AXIS WORKHOLDING SYSTEM A CCESSORIES VB 5 AX 100-H Vise-Set without mounting blocks VB 5 AX 100-L Vise-Set without mounting blocks Mounting blocks without holes Mounting blocks for T-slot, 63 mm Mounting blocks for T-slot, 80 mm Mounting blocks for T-slot, 100 mm Mounting blocks for T-slot, 125 mm Mounting blocks for T-slot, 160 mm Mounting blocks for T-slot, 140 mm Mounting blocks, for location grid 30x30xM10 Mounting blocks, for location grid 40x40xM12 Mounting blocks, for location grid 50x50xM12 Mounting blocks, for location grid 50x50xM16 Mounting blocks, for location grid 40x40xM12...

VB 5AX100 5 AXIS WORKHOLDING SYSTEM E XAMPLES APPLICATION SPOTLIGHT Omnitool, Inc. Reduces Machining Center Need From 2 Machines To 1 Using New Kurt VB 5X100 Schenke 5.1 Clamping System -- 3D Roughing And Face-Milling Operations Performed At 270 In/Min One setup on one machining center does it all – high speed, 5-axis roughing, face-milling and tapping operations to create the intricate three dimensional features of a custom mold cavity. Production time is reduced up to 50 percent. Previously, the mold's upper and lower surfaces were machined on a vertical machining center, then moved to a horizontal...

One Stop Advanced Technology Solutions Custom Gaging Solutions for Automotive, Medical, Aerospace and other manufacturing applications. Kurt Engineered Systems Phone 800-343-9884 www.kurtelectronics.com Vises, Tombstones, VB DockLock, Custom Workholding Systems and Accessories. Kurt™ Manufacturing Industrial Products Division 1325 Quincy St. NE Minneapolis, MN 55413 Tel: (763) 574-8309 Fax: (612) 623-3902 Toll Free (US Only): 1 (877) 226-7823 Toll Free Fax: 1 (877) 226-7828 email address: [email protected] website address: www.kurtworkholding.com © Copyright. All rights reserved www.kurtworkholding.com...